Christie LX700 User Manual Page 69
- Page / 86
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
69
User's Manual
020-000119-01
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described on pages 22–24.
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly
connected.
3. Make sure that all power is switched on.
4. If the projector still does not produce an image, restart your computer.
5. If an image still does not appear, disconnect the projector from your computer and check your computer
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the
projector. Turn on equipment in the order of the projector and computer.)
6. If a problem still persists, check the following solutions.
Appendix
Problem: Solutions
No power.
– Plug the power cord of the projector into the AC outlet.
–
Wait until the POWER indicator stops blinking to turn on the projector again. (See
page 26)
–
Check the WARNING TEMP. indicator. If the WARNING TEMP. indicator is blinking, the
projector cannot be turned on. (See page 68.)
–
Unlock the Key lock function for the projector. (See page 57)
–
See if the filter cartridge is inserted. (See page 62)
– Check the projection lamp. (See page 64.)
PIN code dialog box
appears at start-up.
– PIN code lock is being set. Enter a PIN code; the “1234” or numbers you have set
(See pages 26, 57-58)
The initial display is not
shown.
– Make sure “Off ” or “Countdown Off” are not chosen at Display function.
(See “SETTING” section on page 52)
The initial display is not
same with the default
one.
– Make sure “User” or “Off” are not chosen at Logo select function.
(See “SETTING” section on page 53)
When the projector is on
and you press the input
button, an icon other
than the Lamp mode icon
appears.
– That is the Filter warning icon. (See page 61.)
An icon other than Input
mode or Lamp mode icon
appears.
– That is the Lamp replacement icon or the Filter warning icon. (See pages 60-61.)
No image.
– Check the connection between your computer or video equipment and the projector.
– See if the input signal is correctly output from your computer. Some laptop
computers may need to be changed the setting for monitor output when connected
to the projector. See your computer’s instruction manual for the setting.
– It takes about 30 seconds to display an image after turning on the projector.
– See if the selected system is corresponding with your computer or video equipment.
– Select correct input source once again through menu operation (See pages 35-37).
– Make sure the temperature is not out of Operating Temperature
(41˚F–104˚F [5˚C–
40˚C]).
appears on the screen
–
End of lamp life is approaching. Replace the lamp with a new one promptly. (See
pages 59, 64-65)
Rev. 1 (11/08)
- USER MANUAL 1
- Features and Design 2
- Table of Contents 3
- To The Owner 4
- Safety Instructions 5
- Air Circulation 6
- Moving the Projector 8
- Compliance 9
- Part Names and Functions 10
- Rear Terminal 11
- Side Control and Indicators 13
- Remote Control 14
- User's Manual 16
- 020-000119-01 16
- Remote Control Code 17
- Installation 18
- Removing the lens 19
- Focus adjustment 21
- Focus correction 21
- Monitor Out Signal Table 23
- Connecting for Audio Signal 24
- Connecting the AC Power Cord 25
- Projector side AC Outlet side 25
- Basic Operation 26
- Side Control 28
- On-Screen Menu 28
- Menu Bar 29
- Sound Adjustment 31
- Operating with Remote Control 32
- 3ETTING-ENUP 34
- Input Selection 35
- Menu Operation 36
- Computer Input 38
- Direct Operation 39
- Video Input 45
- Picture Image 49
- SELECTEDP 51
- Enter a Logo PIN code 54
- Change the Logo PIN code 54
- RC sensor 56
- Change the PIN Code 58
- Enter a PIN code 58
- Maintenance and Care 61
- Model No. of your projector 62
- LX700 62
- 003-001726-01 62
- Scroll counter 63
- Filter counter 63
- CAUTION CAUTION 64
- ORDER REPLACEMENT LAMP 65
- Cleaning the Projection Lens 67
- Warning Indicators 68
- Appendix 69
- Computer Input/Video Input 72
- Information Image Adjust 72
- Projector Condition 75
- RESOLUTION 79
- Technical Specifications 80
- Optional Parts 81
- Lens Replacement 81
- DIGITAL DVI-D (DVI 24 PIN) 82
- USB CONNECTOR (Series B) 82
- PIN Code Lock No 83
- Logo PIN Code Lock No 83
- PIN Code Number Memo 83
- Screw Holes for Ceiling Mount 84
- Screw: M6 84
- Depth: 0.393 (10.0) 84
- Americas 86
- Asia Pacific 86
Related products and manuals for Data projectors Christie LX700
Data projectors Christie LWU505 User Manual
(96 pages)
(96 pages)
Data projectors Christie DHD700 User Manual
(88 pages)
(88 pages)
Data projectors Christie L2K1000 User Manual
(102 pages)
(102 pages)
Data projectors Christie Christie HD User Manual
(166 pages)
(166 pages)
Data projectors Christie DS+650 User Manual
(82 pages)
(82 pages)
Data projectors Christie Mirage WU User Manual
(150 pages)
(150 pages)
Data projectors Christie LW720 User Manual
(80 pages)
(80 pages)
Data projectors Christie LX650 User Manual
(78 pages)
(78 pages)
Data projectors Christie L2K1500 User Manual
(102 pages)
(102 pages)
Data projectors Christie LX1200 User Manual
(86 pages)
(86 pages)
© 2020, manymanuals.com. All rights reserved. | 0.424 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals