Christie Christie HD User Manual Page 41
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 2: Installation and Setup
M Series User Manual 2-23
020-100009-08 Rev. 1 (05-2013)
baud rate. See Section 3 Operation for help changing the projector baud rate. To communicate to all projectors,
set the Network Routing to RS-232 and RS-422 Joined.
NOTES: 1) Connect only high quality, properly wired serial communication cables. 2) Each RS-232
communication cable should be no more than 50 feet in length.
Ethernet Network Setup: To add one or more projectors to an Ethernet network, use standard CAT5 cables to
connect each projector Ethernet port to a hub on the network. A controller or PC must also be connected to the
hub.
NOTE: A wireless router can be used to communicate to the projectors via 802.11b/g.
Setting the Projector IP Address, Subnet Mask and Gateway: See 3.7 Configuration - Adjust System
Parameters and Advanced Controls.
Changing the Port Number:
On some Ethernet networks, firewall restrictions may require that the port
number of the projector be changed from the default of 3002. If so, enter a new port number in the Ethernet
Settings menu or include the new port number.
2.9.7 Separate Networks
By default, communications which originate from one type of serial controller—RS-232 vs. RS-422 vs.
Ethernet—stay on the corresponding network path. A “separate” setting indicates this separation for Network
Routing in the Communications menu, see Section 4 Web User Interface. If you are using an RS-422
controller, for example, it will communicate only with the projector to which it is connected unless you change
this setting to either RS-232 and RS-422 Joined or All Joined.
2.9.8 Communicate to all Ports
To relay all messages to all ports—RS-232, RS-422, and Ethernet—set the Network Routing option in the
Communications menu for each projector to All Joined, see Section 4 Web User Interface. This configuration
is useful if you are using a non-RS-232 controller with the RS-232 linking available between these projectors.
- M Series 1
- NOTICES 4
- Table of Contents 10
- 1 Introduction 13
- 1.3 Projector Overview 14
- 1.3.2 User Interface Overview 15
- 1.3.3 List of Components 15
- 1.3.4 Key Features 15
- 1.4.1 General Precautions 16
- 1.4.2 AC/Power Precautions 17
- 1.4.3 Lamp Precautions 17
- 2 Installation and Setup 19
- 2-2 M Series User Manual 20
- 2.1.2 Position the Projector 21
- 2.1.3 Connect a Source 21
- 2.1.4 Connect the Line Cord 22
- 2.1.5 Power up 22
- 2.1.6 Select a Source 22
- 2.1.7 Adjust the Image 22
- 2.2.1 About the Projector 23
- 2-6 M Series User Manual 24
- M Series User Manual 2-7 25
- 2.2.5 Screen Size 26
- 2.2.6 Ambient Lighting 26
- 2.2.7 Ventilation 26
- 2.3 Projector Position 27
- 2-10 M Series User Manual 28
- M Series User Manual 2-11 29
- 2-12 M Series User Manual 30
- 2.4 Mounting 31
- 2.4.3 Stacking 32
- 2.4.5 Stacking Alignment 33
- 2.6 Basic Optical Alignment 34
- P ARROW KEY to cycle to 35
- 2-18 M Series User Manual 36
- 2.8 Power Down 37
- 2.9 Connect Communications 38
- 2.9.4 Connect RS-422 39
- 2.9.5 Ethernet Communications 40
- 2.9.7 Separate Networks 41
- 2-24 M Series User Manual 42
- 2.9.10Configuring the GPIO 43
- 2.10 Projector Communications 44
- 2.11 Connect Sources 45
- 2.11.3Analog BNC Input Card 46
- 2.11.7DMXC Interface Card 47
- Wiring Requirements 48
- M Series User Manual 2-31 49
- IGURE 2-8 1X3 WIRING SOLUTION 49
- IGURE 2-9 2X2 WIRING SOLUTION 49
- 2-32 M Series User Manual 50
- 3 Operation 51
- 3.1.2 Remote Keypad 52
- M Series User Manual 3-3 53
- 3.1.3 Wired Remote 54
- 3.1.4 Built-in Keypad 54
- 3.1.6 Remote Keypad Commands 55
- HANNEL, or you may 56
- 3.2 Navigating the Menus 59
- 3.2.2 On-line Help 60
- 3.2.3 The Global Icon 60
- 3.2.5 Edit Text 62
- 3.3 Using Inputs and Channels 63
- 3.3.2 Create a New Channel 64
- 3.3.3 Using A Channel 64
- 3.3.4 Channel Setup Menu 65
- FIGURE 3-6 COPY A CHANNEL 66
- FIGURE 3-7 DELETE A CHANNEL 66
- 3.4 Adjusting the Image 68
- 3.5 Size and Position Menu 69
- 3.5.9 Blanking - Submenu 72
- 3.6 Image Settings Menu 73
- 3.6.5 Video Options - Submenu 74
- 3.6.6 Input Levels - Submenu 76
- (RED EXAMPLE SHOWN) 78
- 3.6.9 Detail Settings 79
- 3.6.11Color Settings 80
- 3.6.12Dynamic Iris 81
- 3.7.1 Language 82
- 3.7.3 Lens Settings - Submenu 83
- 3.7.5 Date And Time - Submenu 84
- 3.7.10DMX / ArtNET - Submenu 87
- 3.7.11SNMP - Submenu 88
- 3.7.15Edge Blending - Submenu 95
- 3.7.21Tiling Setup - Submenu 99
- Section 3: Operation 100
- 3.8 Lamp Menu 101
- 3.10 Status 105
- 3.11.2Preliminary Calibration 106
- 3.13 Alarm Conditions 109
- 4 Web User Interface 111
- 4.2.1 Help Text 112
- 4.2.2 Basic Operation 113
- Section 3 Operation for more 114
- Section 4: Web User Interface 115
- M Series User Manual 4-7 117
- 5 Maintenance 123
- 5.2 Maintenance of Optics 124
- 5.3 Replacing the Lamps 125
- Section 5: Maintenance 126
- 6 Troubleshooting 127
- 6.3 LCD 128
- 6.4 Remote Keypad 128
- 6.5 OSD 129
- 6.6 Ethernet 129
- 6.7 Displays 129
- Section 6: Troubleshooting 130
- 6.8 Web Interface 131
- 7 Specifications 133
- 7-2 M Series User Manual 134
- 7.1.9 Color Temperature 135
- 7.1.10Convergence 135
- 7.2 Feature Set 136
- 7.2.3 Dust Sealing 137
- 7-6 M Series User Manual 138
- 7.2.12Status LED 139
- 7.2.13Electronics/SW 139
- 7.4.1 Analog (Only) Input 140
- 7.4.2 Twin HDMI Input 140
- 7.4.3 Dual Link DVI Input 141
- 7.4.4 Video Decoder Input 141
- 7.4.5 Dual 3G/HD/SD-SDI 141
- 7.5.1 Projector Control 141
- 7-10 M Series User Manual 142
- 7.6 Power Requirements 143
- 7.7 Physical Specifications 144
- 7.9 Environment 145
- 7.11 Regulatory 146
- Appendix A: Menu Tree 147
- M Series User Manual A-3 149
- A-4 M Series User Manual 150
- M Series User Manual A-5 151
- Appendix B: DMX/ArtNET 153
- B.2 DMX Channel Setup 154
- M Series User Manual B-3 155
- B-4 M Series User Manual 156
- M Series User Manual B-5 157
- B-6 M Series User Manual 158
- M Series User Manual B-7 159
- B-8 M Series User Manual 160
- M Series User Manual B-9 161
- B-10 M Series User Manual 162
- M Series User Manual B-11 163
- B-12 M Series User Manual 164
- ASSY TECH DOCS M Series 165
Related products and manuals for Data projectors Christie Christie HD
Data projectors Christie DS+650 User Manual
(82 pages)
(82 pages)
Data projectors Christie Mirage WU User Manual
(150 pages)
(150 pages)
Data projectors Christie LW720 User Manual
(80 pages)
(80 pages)
Data projectors Christie LX650 User Manual
(78 pages)
(78 pages)
Data projectors Christie L2K1500 User Manual
(102 pages)
(102 pages)
Data projectors Christie LX1200 User Manual
(86 pages)
(86 pages)
© 2020, manymanuals.com. All rights reserved. | 0.366 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals