Christie Christie HD User Manual Page 80
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-30 M Series User Manual
020-100009-08 Rev. 1 (05-2013)
Section 3: Operation
3.6.10Noise Reduction Settings
• Noise Reduction: Selects a filter sensitivity to noise. A higher value may improve noisy sources, but it will
soften the image.
• Block Artifact Reduction: Locates and reduces block edges produced by discrete cosine transform (DCT)
based compression processing.
• Mosquito Noise Reduction: Reduces mosquito artifacts around sharp edges in DCT based compression by
dynamically adapting to image content.
• Split Screen: Provides a snap shot of the main image to be presented on the right side of your screen to allow
evaluation of advanced image processing features. All resizing controls and input card features; such as
color/tint etc, are honoured on both images. However; image processing controls such as the detail-texture,
noise reduction and adaptive contrast features, only occur to the left side image. Changing inputs, channels
or test patterns will disable this control.
NOTE: PIP operation must be disabled prior to enabling this control.
• Full Screen Eye-motion Filter: Select this control to apply the Eye-Motion Filter to the entire screen, rather
than applying just to the edge blending.
• Eye-motion Filter: Allows you to adjust this filter to reduce saccadic eye-motion artifacts, sometimes
noticeable in edge blending regions. Too much filtering may result in loss of detail.
NOTE: For best results, adjust this setting while positioned at the nominal screen viewing distance.
3.6.11Color Settings
• Select Color Adjustment: Select the output color adjustment most suited to this input signal. The options
include the following:
• Max Drives: All color adjustments are turned off allowing the projector to run at maximum brightness.
• Color Temperature: Allows you to specify a color temperature between 3200 and 9300 based on the setting
of the color temperature slide bar.
Expressed in degrees Kelvin [3200K, 5400K, etc.]. Lower numbers appear reddish white and higher
numbers appear bluish.
Standard settings are:
• 9300K, is close to the white of many computer monitors
• 6500K, is the standard for color video, in both standard and high definition forms
• 5400K, is a standard for graphics and black and white video
• 3200K, is useful if the projected image is to be filmed or shot as part of a studio set illuminated with incan-
descent lights
For all color temperatures the color primaries; red, green, and blue are unchanged and reflect the native
colors of the projector.
• SD Video and HD Video: Sets the output color to a specific standard value. Adjusts the colors; red, green,
blue, and white.
• User#: Select 1 of 4 user defined sets of color adjustments; defined in the Configuration menu.
- M Series 1
- NOTICES 4
- Table of Contents 10
- 1 Introduction 13
- 1.3 Projector Overview 14
- 1.3.2 User Interface Overview 15
- 1.3.3 List of Components 15
- 1.3.4 Key Features 15
- 1.4.1 General Precautions 16
- 1.4.2 AC/Power Precautions 17
- 1.4.3 Lamp Precautions 17
- 2 Installation and Setup 19
- 2-2 M Series User Manual 20
- 2.1.2 Position the Projector 21
- 2.1.3 Connect a Source 21
- 2.1.4 Connect the Line Cord 22
- 2.1.5 Power up 22
- 2.1.6 Select a Source 22
- 2.1.7 Adjust the Image 22
- 2.2.1 About the Projector 23
- 2-6 M Series User Manual 24
- M Series User Manual 2-7 25
- 2.2.5 Screen Size 26
- 2.2.6 Ambient Lighting 26
- 2.2.7 Ventilation 26
- 2.3 Projector Position 27
- 2-10 M Series User Manual 28
- M Series User Manual 2-11 29
- 2-12 M Series User Manual 30
- 2.4 Mounting 31
- 2.4.3 Stacking 32
- 2.4.5 Stacking Alignment 33
- 2.6 Basic Optical Alignment 34
- P ARROW KEY to cycle to 35
- 2-18 M Series User Manual 36
- 2.8 Power Down 37
- 2.9 Connect Communications 38
- 2.9.4 Connect RS-422 39
- 2.9.5 Ethernet Communications 40
- 2.9.7 Separate Networks 41
- 2-24 M Series User Manual 42
- 2.9.10Configuring the GPIO 43
- 2.10 Projector Communications 44
- 2.11 Connect Sources 45
- 2.11.3Analog BNC Input Card 46
- 2.11.7DMXC Interface Card 47
- Wiring Requirements 48
- M Series User Manual 2-31 49
- IGURE 2-8 1X3 WIRING SOLUTION 49
- IGURE 2-9 2X2 WIRING SOLUTION 49
- 2-32 M Series User Manual 50
- 3 Operation 51
- 3.1.2 Remote Keypad 52
- M Series User Manual 3-3 53
- 3.1.3 Wired Remote 54
- 3.1.4 Built-in Keypad 54
- 3.1.6 Remote Keypad Commands 55
- HANNEL, or you may 56
- 3.2 Navigating the Menus 59
- 3.2.2 On-line Help 60
- 3.2.3 The Global Icon 60
- 3.2.5 Edit Text 62
- 3.3 Using Inputs and Channels 63
- 3.3.2 Create a New Channel 64
- 3.3.3 Using A Channel 64
- 3.3.4 Channel Setup Menu 65
- FIGURE 3-6 COPY A CHANNEL 66
- FIGURE 3-7 DELETE A CHANNEL 66
- 3.4 Adjusting the Image 68
- 3.5 Size and Position Menu 69
- 3.5.9 Blanking - Submenu 72
- 3.6 Image Settings Menu 73
- 3.6.5 Video Options - Submenu 74
- 3.6.6 Input Levels - Submenu 76
- (RED EXAMPLE SHOWN) 78
- 3.6.9 Detail Settings 79
- 3.6.11Color Settings 80
- 3.6.12Dynamic Iris 81
- 3.7.1 Language 82
- 3.7.3 Lens Settings - Submenu 83
- 3.7.5 Date And Time - Submenu 84
- 3.7.10DMX / ArtNET - Submenu 87
- 3.7.11SNMP - Submenu 88
- 3.7.15Edge Blending - Submenu 95
- 3.7.21Tiling Setup - Submenu 99
- Section 3: Operation 100
- 3.8 Lamp Menu 101
- 3.10 Status 105
- 3.11.2Preliminary Calibration 106
- 3.13 Alarm Conditions 109
- 4 Web User Interface 111
- 4.2.1 Help Text 112
- 4.2.2 Basic Operation 113
- Section 3 Operation for more 114
- Section 4: Web User Interface 115
- M Series User Manual 4-7 117
- 5 Maintenance 123
- 5.2 Maintenance of Optics 124
- 5.3 Replacing the Lamps 125
- Section 5: Maintenance 126
- 6 Troubleshooting 127
- 6.3 LCD 128
- 6.4 Remote Keypad 128
- 6.5 OSD 129
- 6.6 Ethernet 129
- 6.7 Displays 129
- Section 6: Troubleshooting 130
- 6.8 Web Interface 131
- 7 Specifications 133
- 7-2 M Series User Manual 134
- 7.1.9 Color Temperature 135
- 7.1.10Convergence 135
- 7.2 Feature Set 136
- 7.2.3 Dust Sealing 137
- 7-6 M Series User Manual 138
- 7.2.12Status LED 139
- 7.2.13Electronics/SW 139
- 7.4.1 Analog (Only) Input 140
- 7.4.2 Twin HDMI Input 140
- 7.4.3 Dual Link DVI Input 141
- 7.4.4 Video Decoder Input 141
- 7.4.5 Dual 3G/HD/SD-SDI 141
- 7.5.1 Projector Control 141
- 7-10 M Series User Manual 142
- 7.6 Power Requirements 143
- 7.7 Physical Specifications 144
- 7.9 Environment 145
- 7.11 Regulatory 146
- Appendix A: Menu Tree 147
- M Series User Manual A-3 149
- A-4 M Series User Manual 150
- M Series User Manual A-5 151
- Appendix B: DMX/ArtNET 153
- B.2 DMX Channel Setup 154
- M Series User Manual B-3 155
- B-4 M Series User Manual 156
- M Series User Manual B-5 157
- B-6 M Series User Manual 158
- M Series User Manual B-7 159
- B-8 M Series User Manual 160
- M Series User Manual B-9 161
- B-10 M Series User Manual 162
- M Series User Manual B-11 163
- B-12 M Series User Manual 164
- ASSY TECH DOCS M Series 165
Related products and manuals for Data projectors Christie Christie HD
Data projectors Christie DS+650 User Manual
(82 pages)
(82 pages)
Data projectors Christie Mirage WU User Manual
(150 pages)
(150 pages)
Data projectors Christie LW720 User Manual
(80 pages)
(80 pages)
Data projectors Christie LX650 User Manual
(78 pages)
(78 pages)
Data projectors Christie L2K1500 User Manual
(102 pages)
(102 pages)
Data projectors Christie LX1200 User Manual
(86 pages)
(86 pages)
Denon Odtwarzacze podręczniki użytkownika
Zaczynanie od D
Comments to this Manuals