Christie CP2000-X User Manual Page 1

PROJECTION HEAD Parts & Module Replacement 013-100197-02 Rev. 1 (12/06) CP2000-X Parts & Module Replacement 1 1 Ordering Parts...

PARTS & MODULE REPLACEMENT 10 CP2000-X Parts & Module Replacement ETHERNET HUB POWER SUPPLY (10 minutes) The Ethernet hub power supply is Velc

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 11 2) Remove Lamp Blower Vane Switch/mounting bracket assembly (3/8” nut). 3)

PARTS & MODULE REPLACEMENT 12 CP2000-X Parts & Module Replacement GlovesRequiredFANS (SIDE INTAKES) (20 minutes each) Two identical “intake” f

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 13 For each pair of flex cables, connect the top cable from the EFIB to the to

PARTS & MODULE REPLACEMENT 14 CP2000-X Parts & Module Replacement IMPORTANT Back up configuration data files (source, screen, MCGD and TCGD

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 15 LAMINAR AIRFLOW DEVICE (LAD) (20 minutes) The Laminar Airflow Device (LAD)

PARTS & MODULE REPLACEMENT 16 CP2000-X Parts & Module Replacement without the air hoses connected to the LAD. This will prevent any old filter

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 17  Remove the sensor flag (see right).  Remove the small floor insert sur

PARTS & MODULE REPLACEMENT 18 CP2000-X Parts & Module Replacement 7) Tilt the LampLOC/duct assembly towards the rear of the projector. At thi

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 19 2) Remove 2 screws (5/32”) securing the LSM to the projector. See Figure 2

PARTS & MODULE REPLACEMENT 2 CP2000-X Parts & Module Replacement Parts identified throughout may not be available separately. In addition, som

PARTS & MODULE REPLACEMENT 20 CP2000-X Parts & Module Replacement LIQUID COOLING SYSTEM (40 minutes) NOTE: See also Pump and Fan, Heat Exchan

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 21 5) Remove four 5/32” hex screws securing the pump mounting bracket to the

PARTS & MODULE REPLACEMENT 22 CP2000-X Parts & Module Replacement 1. Remove the belly pan so that the hosing under the projector is visible.

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 23 LOW VOLTAGE POWER SUPPLY (LVPS) (30 minutes) The Low Voltage Power Supply (

PARTS & MODULE REPLACEMENT 24 CP2000-X Parts & Module Replacement MOTHERBOARD (25 minutes) The motherboard is located on the floor of the car

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 25 PUMP (30 minutes) The pump is part of the liquid cooling system. To replace

PARTS & MODULE REPLACEMENT 26 CP2000-X Parts & Module Replacement REFLECTOR(S) Refer to the CP2000/XP2000 Parts & Module Replacement Book

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 27 3) Remove 6 Phillips screws securing the SSM to the projector floor. See r

PARTS & MODULE REPLACEMENT 28 CP2000-X Parts & Module Replacement Figure 39. Vane Switch in Exhaust Duct 2) Remove 2 nuts (¼”) securing the

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 29 2) Remove the 2 hex screws (3/32”) securing the lamp vane switch to its mo

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 3 Table 1. CP2000-X Index of Replaceable Parts & Modules Exploded View Lab

PARTS & MODULE REPLACEMENT 4 CP2000-X Parts & Module Replacement Table 2. Other Parts / Options Part Name / Description Part Number RoHS P

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 5 GlovesRequired This section provides instructions for replacing CP2000-X mod

PARTS & MODULE REPLACEMENT 6 CP2000-X Parts & Module Replacement REMOVING THE COVERS (1-5 minutes each) WARNINGS • Fully disconnect from AC

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 7 See right. Unlock igniter door near top edge, and lower the door. If desired

PARTS & MODULE REPLACEMENT 8 CP2000-X Parts & Module Replacement AC DISTRIBUTION MODULE (ACDM) (15 minutes) The AC Distribution Module is loca

PARTS & MODULE REPLACEMENT CP2000-X Parts & Module Replacement 9 3) Disconnect 6 flex cables (3 pairs) and 3 power cables from the EFIB. See