Christie LCD projector User Manual Page 21
- Page / 140
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 2: Installation and Setup
CP2210 User Manual 2-5
020-100410-08 Rev. 1 (05-2014)
2.4 Install the Touch Panel Controller
1. Loosen the mounting arm so that the end fits over the ball joint located on the rear panel of the cinema
projector.
2. Tighten the mounting arm until it fits tightly on the joint.
3. Connect the cable from the TPC to the connector on the rear panel of the cinema projector.
4. Adjust the angle of the TPC.
2.5 Connect Optional Exhaust Ducting
If the room the cinema projector is installed in is not equipped to ventilate up to 11,000 BTU (per hour) you
must install the optional duct (P/N: 119-103105-xx).
Connect the pre-existing external venting ductwork to the optional duct on the side of the cinema projector.
Confirm that there are no obstructions or bends in the ducting, and all air intakes are free of obstructions.
The pre-installed outside-venting duct
should be rigid at the cinema projector and
must also include a heat extractor and blower
that maintains a minimum of 450 CFM*
when the cinema projector is operating at
less than or equal to 25°C ambient and less
than 3,000 feet, when measured at the
cinema projector exhaust opening.
- User Manual 1
- USER MANUAL 3
- NOTICES 4
- Table of Contents 11
- 1 Introduction 13
- 1.3 Power Warnings 14
- 1.4 Lamp Precautions 14
- 1.5 Contact Your Dealer 15
- 2 Installation and Setup 17
- PIB Faceplate Connections 18
- Touch Panel Controller (TPC) 19
- 2-4 CP2210 User Manual 20
- CP2210 User Manual 2-5 21
- 2.6 Install the Primary Lens 22
- 2.10 Install the Lamp 23
- 2.11 Connect Power 24
- CP2210 User Manual 2-9 25
- 2-10 CP2210 User Manual 26
- CP2210 User Manual 2-11 27
- 3.1 Connect a Cinema Server 29
- 3-2 CP2210 User Manual 30
- CP2210 User Manual 3-3 31
- 3-4 CP2210 User Manual 32
- CP2210 User Manual 3-5 33
- 4 Adjusting the Image 35
- 4.3 Basic Image Alignment 36
- 4.4 Adjust Offset 36
- CP2210 User Manual 4-3 37
- Right Boresight Cap Screw 38
- Right Boresight Set Screw 38
- Left Boresight Cap Screw 38
- Left Boresight Set Screw 38
- 4.7 Adjust DMD Convergence 39
- 4.8 Fold Mirror Adjustment 39
- 4.9 Color Calibration 39
- 4.11 Work with 3D 40
- CP2210 User Manual 4-7 41
- 4-8 CP2210 User Manual 42
- CP2210 User Manual 4-9 43
- 4-10 CP2210 User Manual 44
- CP2210 User Manual 4-11 45
- 4.11.10 3D Troubleshooting 46
- 4.12 Present Movies 47
- 4-14 CP2210 User Manual 48
- 4.12.4 Masking 49
- 4.12.6 Select a Source 49
- 5 Operation 51
- Section 3: Operation 52
- 5.5.1 Adjust Lamp Power 53
- 5.5.3 Use LampLOC 53
- 5.5.5 View Lamp Information 54
- 5.5.8 Lamp Expiry Hours 54
- 5.6 Work with Lenses 55
- 5.6.5 Reset the ILS 56
- 5.6.6 Calibrate the ILS 56
- 6 Cinema Projector Menus 57
- 6.2 Main Screen 58
- Control Description 59
- 6.4 User Access and Rights 61
- 6.5 Status Window 63
- 6.6 Alarm Window 67
- 6.7 Interrogator Window 68
- 6.8 SMPTE Errors Window 69
- 6.9 System Logs Window 70
- 6.10 Server Test Window 71
- 6.11 DLP Management Window 72
- 6.12 Network Devices 73
- 6.13 Channel Setup Windows 74
- 6.14 Advanced Setup Windows 80
- 6.14.2 Lamp History Window 82
- Add Lamp Window 83
- 6-28 CP2210 User Manual 84
- 6.14.4 ILS File Setup Window 85
- 6.14.5 Lens Setup Window 86
- Record MCGD Color Settings 89
- 6.15.3 Preferences Window 93
- 6.15.5 Time Setup Window 95
- 6.15.6 Scheduler Window 96
- Configuration 97
- Network Devices Setup Window 98
- 6.15.9 GPIO Setup Window 99
- Calibration 100
- 6.15.11 User Accounts Window 101
- Section 6: Projector Menus 102
- 6.15.12 Upgrade Window 103
- 6.16 Service Setup Windows 104
- 6.16.1 System Access Window 105
- 6.16.2 File Management Window 106
- 6.16.3 LD Marriage Window 107
- 6.16.4 System Access Window 108
- 6.16.5 IMB Marriage Window 109
- 6.17 About Window 110
- 6.18 Help Window 111
- 7 Maintenance 113
- 7.4 Inspect the Lamp 114
- 7.5 Inspect and Clean Optics 114
- 7.6 Clean the Radiator Filter 115
- 7.8 Replace the Lamp 116
- Section 7: Maintenance 117
- Figure 7-2 Lamp Assembly 117
- 7.9 Rotate the Lamp 118
- 7.10 Replace the Air Filter 119
- 7.11 Replace the Lens 120
- Figure 7-7 Install Lens 121
- 8 Troubleshooting 123
- Section 8: Troubleshooting 124
- 8.20 The Display is Faint 127
- Appendix A: Specifications 129
- A.2.1 Cinema Inputs 130
- Appendix B: Specifications 131
- A.3.1 Ethernet Port 133
- A.3.2 RS232-PIB 133
- A.3.3 RS232-ICP 133
- A.3.4 GPIO Port 133
- A.4 Touch Panel Controller 134
- A.5 Power Requirements 135
- (on cinema projector) 135
- A.6 Lamp 135
- A.7 Physical Specifications 136
- A.8 Regulatory 136
- A.9 Environment 137
- A.10 Accessories 137
- *000-101833-07* 139
- ASSY TECH DOCS CP2210 139
Related products and manuals for Projectors Christie LCD projector
Projectors Christie LW600 User Manual
(32 pages)
(32 pages)
Projectors Christie Entero RPMWU Setup Guide
(58 pages)
(58 pages)
Projectors Christie DS+650 User's Guide
(33 pages)
(33 pages)
Projectors Christie q series User Manual
(44 pages)
(44 pages)
Projectors Christie CP2000-X Setup Guide
(64 pages)
(64 pages)
Projectors Christie 4000 User Manual
(4 pages)
(4 pages)
Projectors Christie M-Series User Manual
(12 pages)
(12 pages)
Projectors Christie Mirage 5000 User Manual
(154 pages)
(154 pages)
Projectors Christie LX900 User Manual
(6 pages)
(6 pages)
Projectors Christie CC70HD Specifications
(57 pages)
(57 pages)
Projectors Christie M-Series Setup Guide
(64 pages)
(64 pages)
(40 pages)
Projectors Christie DW series User Manual
(48 pages)
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 0.302 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals