Christie Mirage 5000 User Manual Page 103
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 5
Troubleshooting
User’s Manual 5-1
If the projector does not appear to be operating properly, note the symptoms present and use the following guide to
assist you. If you cannot resolve the problems yourself, contact your dealer for assistance.
NOTE: A qualified service technician
is required when opening the projector to diagnose any “probable cause”.
The projector is on but there’s no display...
1. Was a lens cover accidentally left on? Remove lens cover.
2. Make sure the shutter is OPEN.
3. Is the lamp ignited? Check for interlock problems such as an open lamp door OR
check for light spillage out the back.
4. Is the correct input selected? Check cable connections.
5. Check if menus appear on screen.
6. Can you access test patterns? Make sure there is not a full black test pattern
selected for display—press
Menu
to access test patterns, then cycle patterns
with
keys. Check your source connections again.
Severe motion artifacts…
1. Most likely there is a synchronization problem with reversed 3/2 pull-down in
60Hz-to-24Hz film-to-digital conversion in your source. Correct at the source.
Image appears “squeezed” or vertically stretched into center of screen
1. Check your Resizing selection.
The display is jittery or unstable…
1. If the display is jittery or blinking erratically, ensure that the source is properly
connected and of adequate quality for detection. With a poor quality or
improperly connected source, the projector will repeatedly attempt to display an
image, however briefly.
2. The horizontal or vertical scan frequency of the input signal may be out of range
for the projector. Refer to Section 6, Specifications for scan frequency ranges.
3. The sync signal may be inadequate. Correct the source problem.
The display is faint…
1. Brightness and/or contrast and/or gamma may be set incorrectly.
2. The source may be double terminated. Ensure the source is terminated only once.
3. The source (if non-video) may need a different sync tip clamp location.
5.1 Displays
S
y
m
p
tom '
CAUSE / REMEDY:
S
y
m
p
tom '
CAUSE / REMEDY:
S
y
m
p
tom '
CAUSE / REMEDY:
S
y
m
p
tom '
CAUSE / REMEDY:
S
y
m
p
tom '
CAUSE / REMEDY:
- Table of Contents 1
- Introduction 3
- Installation & Setup 5
- 2.2 Installation 7
- Considerations 7
- %Pixels%Pixels%Pixels%Pixels 10
- User’s Manual 2-7 11
- Figure 2.6 15
- 2.3 Connecting 16
- Sources 16
- (available 2005) 18
- 2.4 Connecting 19
- Communications 19
- Figure 2.12. RS232 Network 20
- Connect a RS422 20
- 2.5 System 21
- Integration 21
- GPIO Connector 21
- 2.6 Power 21
- Connection 21
- Operation 23
- INPUT 5 and/or INPUT 6 24
- REMOTE on the input panel 25
- Figure 3.3. Remote Keypad 26
- C han nel 28
- Contrast 29
- IF WITHIN A MENU: Using the 30
- 3.3 Navigating the 32
- ▼, you can: 34
- Figure 3.8. Entering Text 35
- TO DELETE A CHANNEL 39
- “FULL SIZE” to use 43
- “FULL WIDTH” to fill 43
- “FULL HEIGHT” 43
- — SUBMENU 45
- (SUBJECT-TO-CHANGE) 49
- (RED EXAMPLE SHOWN) 52
- — GENERAL — 56
- Figure 3.14. Communications 58
- — GEOMETRY & COLOR — 60
- Choices 61
- COLOR ADJUSTMENT BY X,Y: Use 62
- COLOR SATURATION: Use this 63
- DIAGNOSTICS / CALIBRATION 64
- 3.7 Working with the 66
- 3.8 Status Menu 69
- 3.9 3D Images 70
- MIRAGE ONLY 70
- Section 3: Operation 72
- User’s Manual 3-53 75
- ✽ ✽ ✽ 1400 x 1050 78
- 3.10 Using Multiple 79
- Projectors 79
- To match reds, decrease “ 81
- To match greens, decrease 81
- Color Saturation Menu 82
- IMPORTANT 84
- • Repeat for each screen 85
- 3.11 Remote Control 88
- of the Projector 88
- 3.12 Error Conditions 89
- Maintenance 93
- 4.2 Cleaning and 96
- Maintenance 96
- 4.3 Replacing 97
- Remote 97
- Batteries 97
- 4.4 Lamp and Filter 97
- Replacement 97
- Figure 4.5 99
- Figure 4.4 99
- Figure 4.6 100
- Figure 4.7 100
- 4.5 Replacing the 101
- Projection Lens 101
- Section 4: Maintenance 102
- User’s Manual 102
- 102
- Troubleshooting 103
- CAUSE / REMEDY: 105
- Specifications 107
- (bi-level, tri-level) 108
- Glossary 113
- Keypad Reference 121
- Serial Communication 123
- C-2 124
- User’s Manual 124
- Throw Distance 125
- Appendix D: Throw Distance 126
- D-2 126
- User’s Manual D-3 127
- D-4 128
- User’s Manual D-5 129
- D-6 130
- User’s Manual D-7 131
- User’s Manual D-9 133
- D-10 134
- System Integration 135
- Optional Input Modules 137
- Ω terminated 140
Related products and manuals for Projectors Christie Mirage 5000
(86 pages)
Projectors Christie Matrix S+ User Manual
(58 pages)
Projectors Christie CC70 Operator's Manual
(58 pages)
(58 pages)
Projectors Christie SXGA+ User Manual
(4 pages)
(4 pages)
Projectors Christie CP2000-M User Manual
(205 pages)
(205 pages)
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
© 2020, manymanuals.com. All rights reserved. | 0.876 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals