Christie Mirage 5000 User Manual Page 21
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 2: Installation and Setup
User’s Manual 2-17.
Regardless of how it is assigned, once a projector has a valid and unique address it
will respond to commands sent to this address. To determine the projector’s current IP
address, consult the Status or Communications menus.
Refer to Section 3 for further information about setting up and using a projector
connected via Ethernet.
Log on to www.christiedigital.com for detailed information on ChristieNET.
General Purpose Input Output
The GPIO connector on the input panel can be used to provide a method of interfacing
a wide range of external I/O devices to the projector.
Refer to Appendix E: System Integration for complete details on pin configuration
and how to program the various pins on the connector.
Plug the line cord to the AC receptacle located at the back of the projector, below the
input panel, and the 3-pronged end into a grounded AC outlet. The input voltage to the
projector must be capable of 100 – 240 VAC in 500W and 1000W models and 200-
240VAC in 1200W models. (See also Section 6 – Specifications for complete details
on all power requirements.)
Use the approved North American-rated line cord supplied with the projector. If you
are connecting to an area outside of North America make sure you are using an
appropriately rated line cord.
Always power down the projector before unplugging the AC line cord. Wait 5-10
minutes for the main exhaust fan to turn off and for the lamp to cool sufficiently
before unplugging the projector.
WARNINGS
Do not attempt operation if the AC supply and cord are
not within the specified voltage and power range.
Wait for the cooling fans to turn off before unplugging the
projector.
2.5 System
Integration -
GPIO Connector
2.6 Power
Connection
- Table of Contents 1
- Introduction 3
- Installation & Setup 5
- 2.2 Installation 7
- Considerations 7
- %Pixels%Pixels%Pixels%Pixels 10
- User’s Manual 2-7 11
- Figure 2.6 15
- 2.3 Connecting 16
- Sources 16
- (available 2005) 18
- 2.4 Connecting 19
- Communications 19
- Figure 2.12. RS232 Network 20
- Connect a RS422 20
- 2.5 System 21
- Integration 21
- GPIO Connector 21
- 2.6 Power 21
- Connection 21
- Operation 23
- INPUT 5 and/or INPUT 6 24
- REMOTE on the input panel 25
- Figure 3.3. Remote Keypad 26
- C han nel 28
- Contrast 29
- IF WITHIN A MENU: Using the 30
- 3.3 Navigating the 32
- ▼, you can: 34
- Figure 3.8. Entering Text 35
- TO DELETE A CHANNEL 39
- “FULL SIZE” to use 43
- “FULL WIDTH” to fill 43
- “FULL HEIGHT” 43
- — SUBMENU 45
- (SUBJECT-TO-CHANGE) 49
- (RED EXAMPLE SHOWN) 52
- — GENERAL — 56
- Figure 3.14. Communications 58
- — GEOMETRY & COLOR — 60
- Choices 61
- COLOR ADJUSTMENT BY X,Y: Use 62
- COLOR SATURATION: Use this 63
- DIAGNOSTICS / CALIBRATION 64
- 3.7 Working with the 66
- 3.8 Status Menu 69
- 3.9 3D Images 70
- MIRAGE ONLY 70
- Section 3: Operation 72
- User’s Manual 3-53 75
- ✽ ✽ ✽ 1400 x 1050 78
- 3.10 Using Multiple 79
- Projectors 79
- To match reds, decrease “ 81
- To match greens, decrease 81
- Color Saturation Menu 82
- IMPORTANT 84
- • Repeat for each screen 85
- 3.11 Remote Control 88
- of the Projector 88
- 3.12 Error Conditions 89
- Maintenance 93
- 4.2 Cleaning and 96
- Maintenance 96
- 4.3 Replacing 97
- Remote 97
- Batteries 97
- 4.4 Lamp and Filter 97
- Replacement 97
- Figure 4.5 99
- Figure 4.4 99
- Figure 4.6 100
- Figure 4.7 100
- 4.5 Replacing the 101
- Projection Lens 101
- Section 4: Maintenance 102
- User’s Manual 102
- 102
- Troubleshooting 103
- CAUSE / REMEDY: 105
- Specifications 107
- (bi-level, tri-level) 108
- Glossary 113
- Keypad Reference 121
- Serial Communication 123
- C-2 124
- User’s Manual 124
- Throw Distance 125
- Appendix D: Throw Distance 126
- D-2 126
- User’s Manual D-3 127
- D-4 128
- User’s Manual D-5 129
- D-6 130
- User’s Manual D-7 131
- User’s Manual D-9 133
- D-10 134
- System Integration 135
- Optional Input Modules 137
- Ω terminated 140
Related products and manuals for Projectors Christie Mirage 5000
(86 pages)
Projectors Christie Matrix S+ User Manual
(58 pages)
Projectors Christie CC70 Operator's Manual
(58 pages)
(58 pages)
Projectors Christie SXGA+ User Manual
(4 pages)
(4 pages)
Projectors Christie CP2000-M User Manual
(205 pages)
(205 pages)
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
© 2020, manymanuals.com. All rights reserved. | 1.849 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals