Christie Mirage 5000 User Manual Page 82
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 3: Operation
3-60
User’s Manual
Using the Color Saturation Menu for Color Matching
You may prefer to use the
Color Saturation menu to
match colors across
multiple screens. In the
three Color Adjustment
submenus (Red, Green,
Blue—see right), set all
main values to 100 and
the secondary values to 0.
Then judge by eye and
adjust the slidebars as
needed. Note that
adjustments here define
new x/y coordinates in the
Color Adjustments by X,Y
menu.
WHAT IS BRIGHTNESS UNIFORMITY? When used to refine screens already matched for
their primary colors (see Matching Colors in Multiple Screens, above) and overall
light output, proper adjustment of Brightness Uniformity can create an exceptionally
smooth screen in which:
• no area of the screen appears more red, green or blue than another
• no area of the screen appears brighter than another
• color and light output from one screen closely matches adjacent screens
Although the Brightness Uniformity control can be used for a stand-alone projector, it
is particularly useful for setting up and maintaining tiled images that form a cohesive
display wall in which the color “cast” and light output appear uniform throughout
each image as well as throughout the entire wall. The procedure provided here
assumes a multiple-screen application.
Before You Begin
Read through the entire procedure before attempting to adjust Brightness Uniformity
controls, and keep in mind the following checklist of prerequisites and guidelines:
ADJUST COLORS FIRST—Always adjust the primary colors as described in the
“Matching Colors in Multiple Screens” procedure (above) before attempting to
work with Brightness Uniformity. This ensures that primary colors, color
temperature, and maximized light output are all well-matched from one screen
to another. These matches are needed before you can achieve good Brightness
Uniformity results.
RUN LAMP FOR 100 HOURS—Light output and Brightness Uniformity can vary
significantly during the first 100 hours of lamp use. For best results with new
lamps, either set up Brightness Uniformity after this period, or do an initial
setup and re-check at 100 hours.
Figure 3.33. Color Matching Using
Color Saturation Menu
A
chieving Brightness '
Uniformit
y
- Table of Contents 1
- Introduction 3
- Installation & Setup 5
- 2.2 Installation 7
- Considerations 7
- %Pixels%Pixels%Pixels%Pixels 10
- User’s Manual 2-7 11
- Figure 2.6 15
- 2.3 Connecting 16
- Sources 16
- (available 2005) 18
- 2.4 Connecting 19
- Communications 19
- Figure 2.12. RS232 Network 20
- Connect a RS422 20
- 2.5 System 21
- Integration 21
- GPIO Connector 21
- 2.6 Power 21
- Connection 21
- Operation 23
- INPUT 5 and/or INPUT 6 24
- REMOTE on the input panel 25
- Figure 3.3. Remote Keypad 26
- C han nel 28
- Contrast 29
- IF WITHIN A MENU: Using the 30
- 3.3 Navigating the 32
- ▼, you can: 34
- Figure 3.8. Entering Text 35
- TO DELETE A CHANNEL 39
- “FULL SIZE” to use 43
- “FULL WIDTH” to fill 43
- “FULL HEIGHT” 43
- — SUBMENU 45
- (SUBJECT-TO-CHANGE) 49
- (RED EXAMPLE SHOWN) 52
- — GENERAL — 56
- Figure 3.14. Communications 58
- — GEOMETRY & COLOR — 60
- Choices 61
- COLOR ADJUSTMENT BY X,Y: Use 62
- COLOR SATURATION: Use this 63
- DIAGNOSTICS / CALIBRATION 64
- 3.7 Working with the 66
- 3.8 Status Menu 69
- 3.9 3D Images 70
- MIRAGE ONLY 70
- Section 3: Operation 72
- User’s Manual 3-53 75
- ✽ ✽ ✽ 1400 x 1050 78
- 3.10 Using Multiple 79
- Projectors 79
- To match reds, decrease “ 81
- To match greens, decrease 81
- Color Saturation Menu 82
- IMPORTANT 84
- • Repeat for each screen 85
- 3.11 Remote Control 88
- of the Projector 88
- 3.12 Error Conditions 89
- Maintenance 93
- 4.2 Cleaning and 96
- Maintenance 96
- 4.3 Replacing 97
- Remote 97
- Batteries 97
- 4.4 Lamp and Filter 97
- Replacement 97
- Figure 4.5 99
- Figure 4.4 99
- Figure 4.6 100
- Figure 4.7 100
- 4.5 Replacing the 101
- Projection Lens 101
- Section 4: Maintenance 102
- User’s Manual 102
- 102
- Troubleshooting 103
- CAUSE / REMEDY: 105
- Specifications 107
- (bi-level, tri-level) 108
- Glossary 113
- Keypad Reference 121
- Serial Communication 123
- C-2 124
- User’s Manual 124
- Throw Distance 125
- Appendix D: Throw Distance 126
- D-2 126
- User’s Manual D-3 127
- D-4 128
- User’s Manual D-5 129
- D-6 130
- User’s Manual D-7 131
- User’s Manual D-9 133
- D-10 134
- System Integration 135
- Optional Input Modules 137
- Ω terminated 140
Related products and manuals for Projectors Christie Mirage 5000
(86 pages)
Projectors Christie Matrix S+ User Manual
(58 pages)
Projectors Christie CC70 Operator's Manual
(58 pages)
(58 pages)
Projectors Christie SXGA+ User Manual
(4 pages)
(4 pages)
Projectors Christie CP2000-M User Manual
(205 pages)
(205 pages)
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
© 2020, manymanuals.com. All rights reserved. | 1.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals