Christie Mirage 5000 User Manual Page 28
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 3: Operation
3-6
User’s Manual
Table 3.1. Auto Setup
What an “Auto Setup” Does
OPTIMIZES: SETS TO DEFAULT:
Pixel Tracking Contrast
Pixel Phase Brightness
Size and Blanking Auto Input Level (off)
Vertical Stretch Detail (if video source)
Position Filter
Input Levels Luma Delay
NOTE: You must have an unlocked channel present to use Auto Setup.
Channel
Press
C han nel
to select a specific source setup (channel) defined and stored in projector
memory. Once you enter a 2-digit channel number (or, if there is a list displayed,
highlight it and press
), the display will automatically change and update
according to the numerous setup parameters defined for that channel. Note that a new
channel is automatically created if you adjust an image from a new source.
NOTE: Channel (
C han nel
)
key behavior during a presentation depends on whether or not
the Display Channel List option is enabled in the Menu Preferences menu. You can
choose to use a scrollable list of channels when you press
C han nel
, or you may prefer to
enter the desired channel number “blind”, i.e., without on-screen feedback. See Menu
Preferences later in this section.
Input 1
Press
Input 1
to display from the data input source connected to BNCs labeled
INPUT 1.
Input 2
Press
Input 2
to display from the DVI source connected to INPUT 2.
Input 3
Press
Input 3
to display from the composite video source connected to INPUT 3.
Input 4
Press
Input 4
to display from the S-video source connected to INPUT 4.
Input 5
Press
Input 5
to display from the INPUT 5 interface module installed in the Option 1 slot.
NOTE: If you have the optional Dual SD/HD-SDI Module installed and there are two
inputs connected here, the second input (B) is considered
INPUT 7. If you are using the
built-in keypad or the
remote keypad, press
INPUT 5 to access INPUT 7 as follows:
• While displaying from
INPUT 5, press
Input 5
again. This switches to INPUT 7.
• While displaying from any input other than the Dual SD/HD-SDI Module,
press
Input 5
. This switches to either INPUT 5 or INPUT 7, depending on which of
the Dual SD/HD-SDI Module inputs (A or B) was last used. Press
Input 5
again to
display from the other Dual SD/HD-SDI Module input.
C han nel
Input 1
Input 2
Input 3
Input 4
Input 5
- Table of Contents 1
- Introduction 3
- Installation & Setup 5
- 2.2 Installation 7
- Considerations 7
- %Pixels%Pixels%Pixels%Pixels 10
- User’s Manual 2-7 11
- Figure 2.6 15
- 2.3 Connecting 16
- Sources 16
- (available 2005) 18
- 2.4 Connecting 19
- Communications 19
- Figure 2.12. RS232 Network 20
- Connect a RS422 20
- 2.5 System 21
- Integration 21
- GPIO Connector 21
- 2.6 Power 21
- Connection 21
- Operation 23
- INPUT 5 and/or INPUT 6 24
- REMOTE on the input panel 25
- Figure 3.3. Remote Keypad 26
- C han nel 28
- Contrast 29
- IF WITHIN A MENU: Using the 30
- 3.3 Navigating the 32
- ▼, you can: 34
- Figure 3.8. Entering Text 35
- TO DELETE A CHANNEL 39
- “FULL SIZE” to use 43
- “FULL WIDTH” to fill 43
- “FULL HEIGHT” 43
- — SUBMENU 45
- (SUBJECT-TO-CHANGE) 49
- (RED EXAMPLE SHOWN) 52
- — GENERAL — 56
- Figure 3.14. Communications 58
- — GEOMETRY & COLOR — 60
- Choices 61
- COLOR ADJUSTMENT BY X,Y: Use 62
- COLOR SATURATION: Use this 63
- DIAGNOSTICS / CALIBRATION 64
- 3.7 Working with the 66
- 3.8 Status Menu 69
- 3.9 3D Images 70
- MIRAGE ONLY 70
- Section 3: Operation 72
- User’s Manual 3-53 75
- ✽ ✽ ✽ 1400 x 1050 78
- 3.10 Using Multiple 79
- Projectors 79
- To match reds, decrease “ 81
- To match greens, decrease 81
- Color Saturation Menu 82
- IMPORTANT 84
- • Repeat for each screen 85
- 3.11 Remote Control 88
- of the Projector 88
- 3.12 Error Conditions 89
- Maintenance 93
- 4.2 Cleaning and 96
- Maintenance 96
- 4.3 Replacing 97
- Remote 97
- Batteries 97
- 4.4 Lamp and Filter 97
- Replacement 97
- Figure 4.5 99
- Figure 4.4 99
- Figure 4.6 100
- Figure 4.7 100
- 4.5 Replacing the 101
- Projection Lens 101
- Section 4: Maintenance 102
- User’s Manual 102
- 102
- Troubleshooting 103
- CAUSE / REMEDY: 105
- Specifications 107
- (bi-level, tri-level) 108
- Glossary 113
- Keypad Reference 121
- Serial Communication 123
- C-2 124
- User’s Manual 124
- Throw Distance 125
- Appendix D: Throw Distance 126
- D-2 126
- User’s Manual D-3 127
- D-4 128
- User’s Manual D-5 129
- D-6 130
- User’s Manual D-7 131
- User’s Manual D-9 133
- D-10 134
- System Integration 135
- Optional Input Modules 137
- Ω terminated 140
Related products and manuals for Projectors Christie Mirage 5000
(86 pages)
Projectors Christie Matrix S+ User Manual
(58 pages)
Projectors Christie CC70 Operator's Manual
(58 pages)
(58 pages)
Projectors Christie SXGA+ User Manual
(4 pages)
(4 pages)
Projectors Christie CP2000-M User Manual
(205 pages)
(205 pages)
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
© 2020, manymanuals.com. All rights reserved. | 1.993 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals