Christie Mirage 5000 User Manual Page 29
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 3: Operation
User’s Manual 3-7.
Input 6
Press
Input 6
to display from the INPUT 6 interface module installed in the Option 2 slot.
NOTE: If you have the optional Dual SD/HD-SDI Module installed and there are two
inputs connected here, the second input (B) is considered
INPUT 8. If you are using the
built-in keypad or the remote keypad, press
INPUT 6 to access INPUT 8 as follows:
• While displaying from
INPUT 6, press
Input 5
again. This switches to INPUT 8.
• While displaying from any input other than the Dual SD/HD-SDI Module,
press
Input 5
. This switches to either INPUT 5 or INPUT 8, depending on which of
the Dual SD/HD-SDI Module inputs (A or B) was last used. Press
Input 5
again
to display from the other Dual SD/HD-SDI Module input.
Contrast
Press
Contrast
to change the amount of white in your images. Use keys until
you reach the desired level of contrast—for best results, start low and increase so that
whites remain bright but are not distorted or tinted and that light areas do not become
white (i.e., “crushed”). Conversely, low contrast causes dim images. See 3.5,
Adjusting the Image (Image Settings subsection).
Brightness
Press
Bright
to increase or decrease the amount of black in the image. Use
keys until you reach the desired level of contrast—for best results, start high and
decrease so that dark areas do not become black (i.e., “crushed”). Conversely, overly
high brightness changes black to dark gray, causing washed-out images. See 3.5,
Adjusting the Image (Image Settings subsection).
Gamma
“Gamma” determines how gray shades are displayed between minimum input (black)
and maximum input (white) for a given amount of signal. The proper setting helps
maintain optimized blacks and whites while ensuring a smooth transition for the “in-
between” values utilized in grays. Unlike brightness and contrast controls, the overall
tone of an image can be lightened or darkened without changing the two extremes and
your images will be more vibrant yet with good detail in dark areas when using the
Gamma control.
The normal gamma setting of 2.2 is correct for most signals and conditions. If excess
ambient light washes out the image and it becomes difficult or impossible to see
details in dark areas, lower the gamma setting to compensate. This will improve
contrast ratio while maintaining good details for blacks and whites
Menu
Press
Menu
to enter or exit the projector’s menu system.
Input 6
Contrast
Bright
Gamma
Menu
- Table of Contents 1
- Introduction 3
- Installation & Setup 5
- 2.2 Installation 7
- Considerations 7
- %Pixels%Pixels%Pixels%Pixels 10
- User’s Manual 2-7 11
- Figure 2.6 15
- 2.3 Connecting 16
- Sources 16
- (available 2005) 18
- 2.4 Connecting 19
- Communications 19
- Figure 2.12. RS232 Network 20
- Connect a RS422 20
- 2.5 System 21
- Integration 21
- GPIO Connector 21
- 2.6 Power 21
- Connection 21
- Operation 23
- INPUT 5 and/or INPUT 6 24
- REMOTE on the input panel 25
- Figure 3.3. Remote Keypad 26
- C han nel 28
- Contrast 29
- IF WITHIN A MENU: Using the 30
- 3.3 Navigating the 32
- ▼, you can: 34
- Figure 3.8. Entering Text 35
- TO DELETE A CHANNEL 39
- “FULL SIZE” to use 43
- “FULL WIDTH” to fill 43
- “FULL HEIGHT” 43
- — SUBMENU 45
- (SUBJECT-TO-CHANGE) 49
- (RED EXAMPLE SHOWN) 52
- — GENERAL — 56
- Figure 3.14. Communications 58
- — GEOMETRY & COLOR — 60
- Choices 61
- COLOR ADJUSTMENT BY X,Y: Use 62
- COLOR SATURATION: Use this 63
- DIAGNOSTICS / CALIBRATION 64
- 3.7 Working with the 66
- 3.8 Status Menu 69
- 3.9 3D Images 70
- MIRAGE ONLY 70
- Section 3: Operation 72
- User’s Manual 3-53 75
- ✽ ✽ ✽ 1400 x 1050 78
- 3.10 Using Multiple 79
- Projectors 79
- To match reds, decrease “ 81
- To match greens, decrease 81
- Color Saturation Menu 82
- IMPORTANT 84
- • Repeat for each screen 85
- 3.11 Remote Control 88
- of the Projector 88
- 3.12 Error Conditions 89
- Maintenance 93
- 4.2 Cleaning and 96
- Maintenance 96
- 4.3 Replacing 97
- Remote 97
- Batteries 97
- 4.4 Lamp and Filter 97
- Replacement 97
- Figure 4.5 99
- Figure 4.4 99
- Figure 4.6 100
- Figure 4.7 100
- 4.5 Replacing the 101
- Projection Lens 101
- Section 4: Maintenance 102
- User’s Manual 102
- 102
- Troubleshooting 103
- CAUSE / REMEDY: 105
- Specifications 107
- (bi-level, tri-level) 108
- Glossary 113
- Keypad Reference 121
- Serial Communication 123
- C-2 124
- User’s Manual 124
- Throw Distance 125
- Appendix D: Throw Distance 126
- D-2 126
- User’s Manual D-3 127
- D-4 128
- User’s Manual D-5 129
- D-6 130
- User’s Manual D-7 131
- User’s Manual D-9 133
- D-10 134
- System Integration 135
- Optional Input Modules 137
- Ω terminated 140
Related products and manuals for Projectors Christie Mirage 5000
(86 pages)
Projectors Christie Matrix S+ User Manual
(58 pages)
Projectors Christie CC70 Operator's Manual
(58 pages)
(58 pages)
Projectors Christie SXGA+ User Manual
(4 pages)
(4 pages)
Projectors Christie CP2000-M User Manual
(205 pages)
(205 pages)
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
© 2020, manymanuals.com. All rights reserved. | 0.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals