Christie CP 2210 User Manual Page 140
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
A-14 CP2210 User Manual
020-100410-07 Rev. 1 (01-2012)
Appendix A: Serial API Commands
SUBCODE DESCRIPTION OF USE
Cxxx Replace Cxxx with the channel number. Valid range is 101-164.
NONE Set lamp mode for the current channel.
EXAMPLES:
(LPM 0) Set Constant Power mode for current channel
(LPM “Constant Power”) Set Constant Power mode for active channel
(LPB+C101 1) Set intensity mode for channel 1
(LPM?) Get Lamp mode for active channel
Lamp Power (LPP)
Set lamp power to be used when in Constant Power mode. NOTE: This command can only be used to update the
current lamp file. Changing the lamp power for the current channel will change the lamp power for any channel
using the same lamp file.
SUBCODE DESCRIPTION OF USE
Cxxx Replace Cxxx with the channel number. Valid range is 101-164.
MINI Get nominal minimum lamp power for the current lamp. Read-only value
NONE Set lamp power for the current channel.
EXAMPLES:
(LPP 2500) Set lamp power to 2500 for current channel
(LPP+C102 2000) Set lamp power to 2000 for channel 2
(LPP+C102?) Get the lamp power for channel 2
Lens Vertical Offset Adjustment (LVO)
Adjust lens offset to specific vertical position with a specific direction. NOTE: This command can only be used to
update the current ILS file. Changing the vertical offset for the current channel will change the vertical offset for
any channel using the same ILS file.
Use command without subcode:
• If ILS is ON, motor will move to specified steps and save data to the active channel.
• If ILS is OFF, motor will move to specified steps. Do not save data to the active channel.
SUBCODE DESCRIPTION OF USE
BACN Motor backlash in negative direction. Read-only.
BACP Motor backlash in positive direction. Read-only. Set only command.
CALB Calibrate travel range and backlash on specified. Only valid parameter for this command is 1. Set only
command.
Cxxx Replace Cxxx with the channel number. Valid range is 101-164.
NONE Moving lens mount to a specified vertical position with a specified direction.
RNGN Motor moving range in negative direction. Read-only.
RNGP Motor moving range in positive direction. Read-only.
RSET Move motor to the center flag then move back to current position. Only valid parameter for this command
is 1. Set only command.
STRT Start motor moving in specified direction, where direction can be (-1, 1). Write-only for v1.3 or newer.
STOP Stops the motor. Write-only for v1.3 or newer.
- User Manual 1
- USER MANUAL 3
- NOTICES 4
- Table of Contents 5
- 1 Introduction 11
- 1.2.1 AC/Power Precautions 12
- 1.2.3 Lamp Precautions 12
- 1.3 Contact Your Dealer 13
- 2 Installation and Setup 15
- 2.2.5 LED Status Indicators 16
- 2.2.7 Projection Lens 16
- 2.2.8 Security Locks 16
- CP2210 User Manual 2-3 17
- 2.3 Position the Projector 18
- Figure 2-2 Adjusting 19
- 2-6 CP2210 User Manual 20
- Figure 2-5 Connect Ducting 21
- 2.7 Install Primary Zoom Lens 22
- 2.8 Install Anamorphic Lens 22
- 2.11 Install Lamp 23
- 2.12 Connect Power 24
- CP2210 User Manual 2-11 25
- 3.1 Connect a Cinema Server 27
- 3-2 CP2210 User Manual 28
- CP2210 User Manual 3-3 29
- 3-4 CP2210 User Manual 30
- CP2210 User Manual 3-5 31
- 4 Adjusting the Image 33
- 4.3 Basic Image Alignment 34
- 4.4 Adjust Offset 34
- CP2210 User Manual 4-3 35
- Right Boresight Cap Screw 36
- Right Boresight Set Screw 36
- Left Boresight Cap Screw 36
- Left Boresight Set Screw 36
- 4.8 Fold Mirror Adjustment 37
- 4.9 Color Calibration 37
- 4.7 Adjust DMD Convergence 37
- 4.11 Work with 3D 38
- CP2210 User Manual 4-7 39
- 4-8 CP2210 User Manual 40
- CP2210 User Manual 4-9 41
- 4-10 CP2210 User Manual 42
- CP2210 User Manual 4-11 43
- 4.11.10 3D Troubleshooting 44
- 4.12 Present Movies 45
- 4-14 CP2210 User Manual 46
- 4.12.4 Masking 47
- 4.12.6 Select a Source 47
- 5 Operation 49
- 5.3 Projector Power States 50
- 5.5 Work with the Lamp 51
- 5.5.5 View Lamp Information 52
- 5.5.8 Lamp Expiry Hours 52
- 5.6 Work with Lenses 53
- 5.6.5 Reset the ILS 54
- 5.6.6 Calibrate the ILS 54
- 6 Projector Menus 55
- 6.2 Main Screen 56
- Control Description 57
- 6.4 User Access and Rights 59
- 6.5 Status Window 61
- 6.6 Alarm Window 65
- 6.7 Interrogator Window 66
- 6.8 SMPTE Errors Window 67
- 6.9 System Logs Window 68
- 6.10 Server Test Window 69
- 6.11 DLP Management Window 70
- 6.12 Network Devices 71
- 6.13 Channel Setup Windows 72
- 6.14 Advanced Setup Windows 78
- 6.14.2 Lamp History Window 80
- Add Lamp Window 81
- 6-28 CP2210 User Manual 82
- 6.14.4 ILS File Setup Window 83
- 6.14.5 Lens Setup Window 84
- Record MCGD Color Settings 87
- 6.15.3 Preferences Window 91
- 6.15.5 Time Setup Window 93
- 6.15.6 Scheduler Window 94
- Configuration 95
- Network Devices Setup Window 96
- 6.15.9 GPIO Setup Window 97
- Calibration 98
- 6.15.11 User Accounts Window 99
- Section 6: Projector Menus 100
- 6.15.12 Upgrade Window 101
- 6.16 Service Setup Windows 102
- 6.16.1 System Access Window 103
- 6.16.2 File Management Window 104
- 6.16.3 LD Marriage Window 105
- 6.16.4 System Access Window 106
- 6.16.5 IMB Marriage Window 107
- 6.17 About Window 108
- 6.18 Help Window 109
- 7 Maintenance 111
- 7.4 Inspect the Lamp 112
- 7.5 Inspect and Clean Optics 112
- 7.6 Clean the Radiator Filter 113
- 7.8 Replace the Lamp 114
- Section 7: Maintenance 115
- Figure 7-2 Lamp Assembly 115
- 7.9 Rotate the Lamp 116
- 7.10 Replace the Air Filter 117
- 7.11 Replace the Lens 118
- Figure 7-7 Install Lens 119
- 8 Troubleshooting 121
- Section 8: Troubleshooting 122
- 8.20 The Display is Faint 125
- A.1 Function Codes 127
- A-2 CP2210 User Manual 128
- CP2210 User Manual A-3 129
- A-4 CP2210 User Manual 130
- CP2210 User Manual A-5 131
- A-6 CP2210 User Manual 132
- CP2210 User Manual A-7 133
- A-8 CP2210 User Manual 134
- CP2210 User Manual A-9 135
- A-10 CP2210 User Manual 136
- CP2210 User Manual A-11 137
- A-12 CP2210 User Manual 138
- CP2210 User Manual A-13 139
- A-14 CP2210 User Manual 140
- CP2210 User Manual A-15 141
- A-16 CP2210 User Manual 142
- CP2210 User Manual A-17 143
- A-18 CP2210 User Manual 144
- CP2210 User Manual A-19 145
- Stop communications to DLP 146
- CP2210 User Manual A-21 147
- A-22 CP2210 User Manual 148
- CP2210 User Manual A-23 149
- A-24 CP2210 User Manual 150
- CP2210 User Manual A-25 151
- Appendix B: Specifications 153
- B.2.1 Cinema Inputs 154
- B.3.1 Ethernet Port 157
- B.3.2 RS232-PIB 157
- B.3.3 RS232-ICP 157
- B.3.4 GPIO Port 157
- B.4 Touch Panel Controller 158
- B.5 Power Requirements 159
- (on projector) 159
- B.6 Lamp 159
- B.7 Physical Specifications 160
- B.8 Regulatory 160
- B.9 Environment 161
- B.10 Accessories 161
- *000-101833-07* 163
- ASSY TECH DOCS CP2210 163
Related products and manuals for Data projectors Christie CP 2210
Data projectors Christie LX750 User Manual
(80 pages)
(80 pages)
Data projectors Christie LX700 User Manual
(86 pages)
(86 pages)
Data projectors Christie LWU505 User Manual
(96 pages)
(96 pages)
Data projectors Christie DHD700 User Manual
(88 pages)
(88 pages)
Data projectors Christie L2K1000 User Manual
(102 pages)
(102 pages)
Data projectors Christie Christie HD User Manual
(166 pages)
(166 pages)
Data projectors Christie DS+650 User Manual
(82 pages)
(82 pages)
Data projectors Christie Mirage WU User Manual
(150 pages)
(150 pages)
Data projectors Christie LW720 User Manual
(80 pages)
(80 pages)
Data projectors Christie LX650 User Manual
(78 pages)
(78 pages)
Data projectors Christie L2K1500 User Manual
(102 pages)
(102 pages)
Data projectors Christie LX1200 User Manual
(86 pages)
(86 pages)
© 2020, manymanuals.com. All rights reserved. | 0.205 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals