Christie CP 2210 User Manual Page 141
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Appendix A: Serial API Commands
CP2210 User Manual A-15
020-100410-07 Rev. 1 (01-2012)
MOVR Moves the motor a given number of steps based on the current location. Write-only for v1.3 or newer.
EXAMPLES:
(LVO 500 1) Move lens to position 500 along vertical axis with positive approach
(LVO 500 -1) Move lens to position 500 along vertical axis with negative approach
(LVO+C101 -500 1) Set lens vertical position for channel 1 to -500 with positive approach
(LVO ?) Return current motor position along vertical axis and direction
(LVO+CALB 1) Calibrate the vertical axis
(LVO+RSET 1) Reset the vertical axis
(LVO+STRT 1) Starts motor moving in positive direction
(LVO+STOP) Stops motor
(LVO+MOVR -100) Move motor 100 steps in negative direction
(LVO+MOVR 200) Move motor 200 steps in positive direction
Measured Color (MCG)
Select the Measured Color Gamut file. This file describes the native colorimetry for the projector as installed and is
required for accurate color processing in the cinema electronics. This control is per channel to allow for different
colorimetry for applications such as 3D.
SUBCODE DESCRIPTION OF USE
Cxxx Replace xxx with the channel number. Valid range is 101 - 164.
NONE Select measured color gamut for the current channel.
EXAMPLES:
(MCG+C108 “Nominal”) Use file “Nominal” on channel 108
(MCG+C108?) Get measured color file name on channel 108
(MCG?L) List all entries of measured color control
Channel Name (NAM)
Set the descriptive channel name for the specified channel
SUBCODE DESCRIPTION OF USE
Cxxx Replace xxx with the channel number. Valid range is 101 - 164.
NONE Select channel name for the current channel.
EXAMPLES:
(NAM+C108 “Scope 2.39”) Set channel name for channel 108
(NAM+C108?) Get channel name for channel 108
Network Setup (NET)
Set the network parameters for Eth0, Gateway, and Subnet 0.
SUBCODE DESCRIPTION OF USE
DLP0 Set the IP address for the MGMT Ethernet controller (deprecated).
ETH0 Set the WAN IP address for the projector
GATE Set the WAN Gateway for the projector
HOST Host name
MAC0 Gets the MAC address of the projector
SUB0 Set the WAN subnet mask for the projector
- User Manual 1
- USER MANUAL 3
- NOTICES 4
- Table of Contents 5
- 1 Introduction 11
- 1.2.1 AC/Power Precautions 12
- 1.2.3 Lamp Precautions 12
- 1.3 Contact Your Dealer 13
- 2 Installation and Setup 15
- 2.2.5 LED Status Indicators 16
- 2.2.7 Projection Lens 16
- 2.2.8 Security Locks 16
- CP2210 User Manual 2-3 17
- 2.3 Position the Projector 18
- Figure 2-2 Adjusting 19
- 2-6 CP2210 User Manual 20
- Figure 2-5 Connect Ducting 21
- 2.7 Install Primary Zoom Lens 22
- 2.8 Install Anamorphic Lens 22
- 2.11 Install Lamp 23
- 2.12 Connect Power 24
- CP2210 User Manual 2-11 25
- 3.1 Connect a Cinema Server 27
- 3-2 CP2210 User Manual 28
- CP2210 User Manual 3-3 29
- 3-4 CP2210 User Manual 30
- CP2210 User Manual 3-5 31
- 4 Adjusting the Image 33
- 4.3 Basic Image Alignment 34
- 4.4 Adjust Offset 34
- CP2210 User Manual 4-3 35
- Right Boresight Cap Screw 36
- Right Boresight Set Screw 36
- Left Boresight Cap Screw 36
- Left Boresight Set Screw 36
- 4.8 Fold Mirror Adjustment 37
- 4.9 Color Calibration 37
- 4.7 Adjust DMD Convergence 37
- 4.11 Work with 3D 38
- CP2210 User Manual 4-7 39
- 4-8 CP2210 User Manual 40
- CP2210 User Manual 4-9 41
- 4-10 CP2210 User Manual 42
- CP2210 User Manual 4-11 43
- 4.11.10 3D Troubleshooting 44
- 4.12 Present Movies 45
- 4-14 CP2210 User Manual 46
- 4.12.4 Masking 47
- 4.12.6 Select a Source 47
- 5 Operation 49
- 5.3 Projector Power States 50
- 5.5 Work with the Lamp 51
- 5.5.5 View Lamp Information 52
- 5.5.8 Lamp Expiry Hours 52
- 5.6 Work with Lenses 53
- 5.6.5 Reset the ILS 54
- 5.6.6 Calibrate the ILS 54
- 6 Projector Menus 55
- 6.2 Main Screen 56
- Control Description 57
- 6.4 User Access and Rights 59
- 6.5 Status Window 61
- 6.6 Alarm Window 65
- 6.7 Interrogator Window 66
- 6.8 SMPTE Errors Window 67
- 6.9 System Logs Window 68
- 6.10 Server Test Window 69
- 6.11 DLP Management Window 70
- 6.12 Network Devices 71
- 6.13 Channel Setup Windows 72
- 6.14 Advanced Setup Windows 78
- 6.14.2 Lamp History Window 80
- Add Lamp Window 81
- 6-28 CP2210 User Manual 82
- 6.14.4 ILS File Setup Window 83
- 6.14.5 Lens Setup Window 84
- Record MCGD Color Settings 87
- 6.15.3 Preferences Window 91
- 6.15.5 Time Setup Window 93
- 6.15.6 Scheduler Window 94
- Configuration 95
- Network Devices Setup Window 96
- 6.15.9 GPIO Setup Window 97
- Calibration 98
- 6.15.11 User Accounts Window 99
- Section 6: Projector Menus 100
- 6.15.12 Upgrade Window 101
- 6.16 Service Setup Windows 102
- 6.16.1 System Access Window 103
- 6.16.2 File Management Window 104
- 6.16.3 LD Marriage Window 105
- 6.16.4 System Access Window 106
- 6.16.5 IMB Marriage Window 107
- 6.17 About Window 108
- 6.18 Help Window 109
- 7 Maintenance 111
- 7.4 Inspect the Lamp 112
- 7.5 Inspect and Clean Optics 112
- 7.6 Clean the Radiator Filter 113
- 7.8 Replace the Lamp 114
- Section 7: Maintenance 115
- Figure 7-2 Lamp Assembly 115
- 7.9 Rotate the Lamp 116
- 7.10 Replace the Air Filter 117
- 7.11 Replace the Lens 118
- Figure 7-7 Install Lens 119
- 8 Troubleshooting 121
- Section 8: Troubleshooting 122
- 8.20 The Display is Faint 125
- A.1 Function Codes 127
- A-2 CP2210 User Manual 128
- CP2210 User Manual A-3 129
- A-4 CP2210 User Manual 130
- CP2210 User Manual A-5 131
- A-6 CP2210 User Manual 132
- CP2210 User Manual A-7 133
- A-8 CP2210 User Manual 134
- CP2210 User Manual A-9 135
- A-10 CP2210 User Manual 136
- CP2210 User Manual A-11 137
- A-12 CP2210 User Manual 138
- CP2210 User Manual A-13 139
- A-14 CP2210 User Manual 140
- CP2210 User Manual A-15 141
- A-16 CP2210 User Manual 142
- CP2210 User Manual A-17 143
- A-18 CP2210 User Manual 144
- CP2210 User Manual A-19 145
- Stop communications to DLP 146
- CP2210 User Manual A-21 147
- A-22 CP2210 User Manual 148
- CP2210 User Manual A-23 149
- A-24 CP2210 User Manual 150
- CP2210 User Manual A-25 151
- Appendix B: Specifications 153
- B.2.1 Cinema Inputs 154
- B.3.1 Ethernet Port 157
- B.3.2 RS232-PIB 157
- B.3.3 RS232-ICP 157
- B.3.4 GPIO Port 157
- B.4 Touch Panel Controller 158
- B.5 Power Requirements 159
- (on projector) 159
- B.6 Lamp 159
- B.7 Physical Specifications 160
- B.8 Regulatory 160
- B.9 Environment 161
- B.10 Accessories 161
- *000-101833-07* 163
- ASSY TECH DOCS CP2210 163
Related products and manuals for Data projectors Christie CP 2210
Data projectors Christie LX750 User Manual
(80 pages)
(80 pages)
Data projectors Christie LX700 User Manual
(86 pages)
(86 pages)
Data projectors Christie LWU505 User Manual
(96 pages)
(96 pages)
Data projectors Christie DHD700 User Manual
(88 pages)
(88 pages)
Data projectors Christie L2K1000 User Manual
(102 pages)
(102 pages)
Data projectors Christie Christie HD User Manual
(166 pages)
(166 pages)
Data projectors Christie DS+650 User Manual
(82 pages)
(82 pages)
Data projectors Christie Mirage WU User Manual
(150 pages)
(150 pages)
Data projectors Christie LW720 User Manual
(80 pages)
(80 pages)
Data projectors Christie LX650 User Manual
(78 pages)
(78 pages)
Data projectors Christie L2K1500 User Manual
(102 pages)
(102 pages)
Data projectors Christie LX1200 User Manual
(86 pages)
(86 pages)
© 2020, manymanuals.com. All rights reserved. | 1.545 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals