Christie CP2000-M User Manual Page 134
- Page / 205
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 6: Maintenance
CP2000-SB User Manual 6-3
020-100162-04 Rev. 1 (05-2009)
6.1.3 AC/Power Precautions
Installation of this projector requires that an electrician hard-wire a 3-phase (Y) feed and a separate 15A
single-phase feed from the pedestal toe to the AC supply in your building. You must also use only the correct
pedestal for your geographic area as stated in
Section 1.2.2 Software Requirements.
Operate the projector at the specified voltage.
Warning! Do not attempt operation if the AC supply and
pedestal are not within the specified voltage range.
Do not allow anything to rest on the power cord. Locate the projector where the cord cannot be abused by
persons walking on it or objects rolling over it. Never operate the projector if the power cable appears damaged
in any way. Do not overload power outlets and extension cords as this can result in fire or shock hazards.
NOTE: Only qualified service technicians are permitted to open any enclosure on the product, and only if AC
has been fully disconnected at BOTH wall breakers. Warning! SHOCK HAZARD. Disconnect from AC
before opening any enclosure. Disconnect at BOTH
wall breakers.
6.1.4 Lamp Precautions
Any Xenon arc lamp used in the CP2000-SB is under high pressure and must be handled with great care at all
times. Lamps may explode if dropped or mishandled.
WEAR PROTECTIVE CLOTHING:
Never open the lamp door unless you are wearing authorized protective clothing such as that included in a
Christie Protective Clothing Safety Kit P/N 598900-095. Recommended protective clothing includes-but may
not be limited to-protective gloves, latex lab gloves, double-layer 0.040" acetate face shield, and a quilted
ballistic nylon jacket or a welder's jacket.
Warning! 1) EXPLOSION HAZARD -Wear authorized protective
clothing whenever the lamp door is open! 2) Never attempt to remove the lamp directly after use. The lamp is
under increased pressure when hot and may explode, causing personal injury and/or property damage. Allow
to cool completely.
NOTES: 1) Christie's protective clothing recommendations are subject to change. 2) Any local or federal
specifications take precedence over Christie recommendations.
COOL THE LAMP COMPLETELY:
The arc lamp operates at a very high pressure that increases with temperature. Failure to allow the
lamp to sufficiently cool prior to handling increases the potential for an explosion causing personal
injury and/or property damage. After turning the lamp OFF, it is crucial that you wait
at least 10
minutes before turning off the rest of the projector breakers, disconnecting AC and opening the
lamp door. This provides enough time for the internal lamp cooling fans to properly cool the lamp. Cool
completely before handling. Again, always wear protective clothing! Warning! 1) Never attempt to access
the lamp while the lamp is on. Wait at least 10 min. after lamp shut-off before powering down, disconnecting
from AC and opening the lamp door. 2) SHOCK HAZARD. Disconnect from AC at BOTH
wall breakers before
opening the lamphouse.
For all other precautions critical for safe removal and replacement of the lamp, refer to
Section 6.4 Replacing the Lamp & Filter.
- Film-Tech 1
- CP2000-SB 2
- Table of Contents 10
- 1 Introduction 12
- 1.1 The Projector 13
- 1.2 List of Components 14
- 1.2.2 Software Requirements 15
- 1.4.1 Typographical Notations 16
- LP, A1 etc 16
- 2 Installation & Setup 18
- Before You Begin 19
- CP2000-SB User Manual 2-3 20
- Figure 2-3 Adjust Feet 21
- Interlocks to Projection Head 22
- Cables to Projection Head 23
- Connections to Power 23
- CONNECT LAMP LEADS: 24
- 2-8 CP2000-SB User Manual 25
- CP2000-SB User Manual 2-9 26
- Figure 2-16 Fill Reservoir 27
- 2.1.2 Exhaust Ducting 28
- 2.1.3 Lens(es) 29
- Primary Zoom Lens 29
- 2.1.4 Install First Lamp 29
- 2.1.5 Connecting to Power 30
- Warning! Ground 31
- CP2000-SB User Manual 2-15 32
- IF EXTERNAL 33
- IF INTERNAL 34
- 2-18 CP2000-SB User Manual 35
- PC/Laptop, Server or Network 36
- 2-20 CP2000-SB User Manual 37
- 2.5 Initial Power Up 38
- 2.6 Maximizing Light Output 39
- 2.7 Basic Image Alignment 40
- 2.8.1 Adjust Offset 41
- CP2000-SB User Manual 2-25 42
- Focus Left 43
- Edge Center 43
- Vertical Boresight Bolt 44
- Vertical Hold Screw 44
- Top Center 44
- 2.8.5 Add Auxiliary Lens 45
- Anamorphic (1.25x) 45
- Wide Converter Lens (1.26x) 45
- Fold Mirror Adjustment 46
- DMD Convergence 46
- Color Calibration 47
- Electronic Screen Masking 47
- PCFs (Rare) 47
- 3 Operation 48
- 3.1 Projector Basics 49
- Air Filter 50
- Breaker Panel 50
- Power Cabling 52
- Projection Head 52
- Security Locks 52
- Security Plates 52
- 3.2 Power-up Procedure 53
- 3.3 Power-down Procedure 54
- 3.4.1 User Access and Rights 55
- General Users 55
- 3.4.2 TPC Power-up Defaults 56
- 3.4.3 Failed TPC Connection 56
- 3.5.1 TPC Main Menu 58
- 3.5.2 TPC Status Menu 59
- ENVIRONMENT 61
- 3.5.3 TPC Alarm Window 63
- Responding to an Alarm Window 64
- 3.5.4 TPC Custom Menu 65
- Custom: Page-1 Menu 66
- = use full cinema processing 67
- Custom: Page-2 Menu 68
- Custom: 3D Control Menu 69
- L/R INPUT REFERENCE NOTES: 70
- L/R DISPLAY REFERENCE NOTES: 70
- L/R OUTPUT POLARITY NOTES: 70
- FRAME RATE N:M NOTES: 70
- Advanced: Preference Menu 75
- for a complete description 75
- New Lamp button activates a 76
- Table 3.11 New Lamp Fields 77
- Figure 3-18 New Lamp Fields 77
- Advanced: Lens Menu 78
- Advanced Preferences menu 79
- Admin Menus 82
- RESOLUTION NOTES: 83
- 0 (default) to 84
- Table 3.15 84
- PRESENTATION NOTES: 86
- CROPPING NOTES: 86
- LETTER BOX NOTES: 87
- : OnSite is a permanent 88
- MEASURED (MCGD) NOTES: 89
- CREATE MCGD NOTES: 89
- GAIN NOTES: 89
- CP2000-SB User Manual 3-43 90
- Record any new 91
- IP Address 92
- Figure 3-38 About Menu 96
- Section 3: Operation 100
- Table 3.22 Sample Messages 100
- 3.7 Upgrading SSM Firmware 102
- Figure 3-43 Host Setting 103
- 3.8 Working with the Lamp 104
- WHEN SHOULD I USE LiteLOC™? 105
- Figure 3-46 Setting LiteLOC™ 105
- Advanced: Lamp History menu 109
- 3.9 Working with the Lens 111
- 3.10 Working with 3D 113
- 3.10.4 Other Hardware Setups 115
- Figure 3-58 Setup for 3D 116
- 4 Cinema Operation 120
- 4.1 Compatible Cinema Sources 121
- Section 4: Cinema Operation 122
- 4.2 Image Formats 123
- Figure 4-4 also has 124
- Figure 4-5) 124
- 5 Non-Cinema Operation 128
- Table 5.1 129
- Figure 5-2) 129
- CP2000-SB User Manual 5-3 130
- 5.2 Selecting the Source 131
- 6 Maintenance 132
- 6.1 Warnings and Guidelines 133
- Section 6: Maintenance 134
- WEAR PROTECTIVE CLOTHING: 134
- COOL THE LAMP COMPLETELY: 134
- FILLING THE COOLER: 135
- 6.3 Maintenance and Cleaning 136
- For lens only 137
- For reflector only 137
- Figure 6-1 Install Bulb 140
- 6.5 Replacing a Lens 143
- 7 Troubleshooting 144
- 7.1 Power 145
- 7.2 Lamp 145
- Section 7: Troubleshooting 146
- 7.4 Ethernet 147
- 7.5 Cinema Displays 147
- 7.6 Non-Cinema Displays 148
- 8 Specifications 150
- 8.1 Display 151
- 8.2 Lenses 151
- 8.3 Inputs 152
- 8.4 Touch Panel Controller 153
- 8.5 Power Specifications 153
- 8.6 Lamps 154
- 8.7 Regulatory 155
- 8.8 Environment 156
- 8.9 Weight & Size 156
- Section 8: Specifications 157
- 8.10 Standard Components 158
- Appendix A: Glossary 160
- Appendix B: ASCII Messages 176
- B.1 Function Codes 177
- ASCIICODE?M) 189
- Table B.2 Error Messages 190
- CP2000-SB User Manual B-19 194
- P1 P2 Notes 195
- C.1 Serial Links to Projector 200
- CP2000-SB User Manual D-1 202
- D.1 The GPIO Port 203
- CP2000-SB User Manual E-1 204
- E-2 CP2000-SB User Manual 205
Related products and manuals for Projectors Christie CP2000-M
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
Projectors Christie L2K1500 User Manual
(36 pages)
(36 pages)
Projectors Christie DHD800 User Manual
(97 pages)
(97 pages)
Projectors Christie LW600 User Manual
(101 pages)
(101 pages)
© 2020, manymanuals.com. All rights reserved. | 0.865 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals