Christie CP2000-M User Manual Page 82
- Page / 205
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 3: Operation
CP2000-SB User Manual 3-35
020-100162-04 Rev. 1 (05-2009)
3.5.6 TPC Admin Menu
NOTE: Password-protected; Administrators, installers and service
technicians only.
The seven Admin submenus offer a broad range of options used primarily
for defining how the projector will respond to incoming sources in the
given environment, or for adjusting a major system parameter affecting
overall performance. Five of the
Admin submenus-Source, Screen,
Gamut, IP Config
and GPIO-are available to both administrators and
installers. Two others-General and Lamp-are restricted to installers
(service) only. See
Figure 3-23. Other users cannot access Admin.
Admin: Source Menu
Incoming sources can vary widely in their current resolution and original
aspect ratio. The projector must be able to respond to the myriad of
possible combinations, projecting full images of the desired size, content,
and proportion in every case. This consistency is achieved by creating a
variety of
source files in projector memory, each of which indicates the
following for the projector:
• Incoming
resolution (# pixels across, # pixels top-to-bottom)
•
Offset desired (i.e., amount of data to discard. Rare.)
• Desired
aspect ratio (i.e., the original display format to be recovered)
Although in rare cases the content distributor may include this source information as part of a pre-defined PCF
(applied by using the PCF in the projector), alternatively these variables can be defined either in the Source
submenu in the TPC as described here, or by using
DCP Librarian. With a good collection of assorted source
files available in memory, the proper file can then be quickly chosen from within the
Custom menu for
implementation in the projector whenever a matching input signal is encountered.
Note that for any source, the projector relies on
Source file settings as well as Screen file settings. See also
Admin: Screen menu.
Figure 3-23 Access Rights for
Admin Menus
Figure 3-24 Admin: Source Menu Options
Incoming Format.
Amount to discard.
(“+” value will
discard data from
top and/or left,
“-” value will
discard from
bottom and right).
Save settings in a
source file for
access in Custom
menu.
Cancel new
(unsaved) source
settings.
Width-to-height
image proportion
desired.
Adjust x/y
resolution and off-
set as desired.
Test in display
without saving.
- Film-Tech 1
- CP2000-SB 2
- Table of Contents 10
- 1 Introduction 12
- 1.1 The Projector 13
- 1.2 List of Components 14
- 1.2.2 Software Requirements 15
- 1.4.1 Typographical Notations 16
- LP, A1 etc 16
- 2 Installation & Setup 18
- Before You Begin 19
- CP2000-SB User Manual 2-3 20
- Figure 2-3 Adjust Feet 21
- Interlocks to Projection Head 22
- Cables to Projection Head 23
- Connections to Power 23
- CONNECT LAMP LEADS: 24
- 2-8 CP2000-SB User Manual 25
- CP2000-SB User Manual 2-9 26
- Figure 2-16 Fill Reservoir 27
- 2.1.2 Exhaust Ducting 28
- 2.1.3 Lens(es) 29
- Primary Zoom Lens 29
- 2.1.4 Install First Lamp 29
- 2.1.5 Connecting to Power 30
- Warning! Ground 31
- CP2000-SB User Manual 2-15 32
- IF EXTERNAL 33
- IF INTERNAL 34
- 2-18 CP2000-SB User Manual 35
- PC/Laptop, Server or Network 36
- 2-20 CP2000-SB User Manual 37
- 2.5 Initial Power Up 38
- 2.6 Maximizing Light Output 39
- 2.7 Basic Image Alignment 40
- 2.8.1 Adjust Offset 41
- CP2000-SB User Manual 2-25 42
- Focus Left 43
- Edge Center 43
- Vertical Boresight Bolt 44
- Vertical Hold Screw 44
- Top Center 44
- 2.8.5 Add Auxiliary Lens 45
- Anamorphic (1.25x) 45
- Wide Converter Lens (1.26x) 45
- Fold Mirror Adjustment 46
- DMD Convergence 46
- Color Calibration 47
- Electronic Screen Masking 47
- PCFs (Rare) 47
- 3 Operation 48
- 3.1 Projector Basics 49
- Air Filter 50
- Breaker Panel 50
- Power Cabling 52
- Projection Head 52
- Security Locks 52
- Security Plates 52
- 3.2 Power-up Procedure 53
- 3.3 Power-down Procedure 54
- 3.4.1 User Access and Rights 55
- General Users 55
- 3.4.2 TPC Power-up Defaults 56
- 3.4.3 Failed TPC Connection 56
- 3.5.1 TPC Main Menu 58
- 3.5.2 TPC Status Menu 59
- ENVIRONMENT 61
- 3.5.3 TPC Alarm Window 63
- Responding to an Alarm Window 64
- 3.5.4 TPC Custom Menu 65
- Custom: Page-1 Menu 66
- = use full cinema processing 67
- Custom: Page-2 Menu 68
- Custom: 3D Control Menu 69
- L/R INPUT REFERENCE NOTES: 70
- L/R DISPLAY REFERENCE NOTES: 70
- L/R OUTPUT POLARITY NOTES: 70
- FRAME RATE N:M NOTES: 70
- Advanced: Preference Menu 75
- for a complete description 75
- New Lamp button activates a 76
- Table 3.11 New Lamp Fields 77
- Figure 3-18 New Lamp Fields 77
- Advanced: Lens Menu 78
- Advanced Preferences menu 79
- Admin Menus 82
- RESOLUTION NOTES: 83
- 0 (default) to 84
- Table 3.15 84
- PRESENTATION NOTES: 86
- CROPPING NOTES: 86
- LETTER BOX NOTES: 87
- : OnSite is a permanent 88
- MEASURED (MCGD) NOTES: 89
- CREATE MCGD NOTES: 89
- GAIN NOTES: 89
- CP2000-SB User Manual 3-43 90
- Record any new 91
- IP Address 92
- Figure 3-38 About Menu 96
- Section 3: Operation 100
- Table 3.22 Sample Messages 100
- 3.7 Upgrading SSM Firmware 102
- Figure 3-43 Host Setting 103
- 3.8 Working with the Lamp 104
- WHEN SHOULD I USE LiteLOC™? 105
- Figure 3-46 Setting LiteLOC™ 105
- Advanced: Lamp History menu 109
- 3.9 Working with the Lens 111
- 3.10 Working with 3D 113
- 3.10.4 Other Hardware Setups 115
- Figure 3-58 Setup for 3D 116
- 4 Cinema Operation 120
- 4.1 Compatible Cinema Sources 121
- Section 4: Cinema Operation 122
- 4.2 Image Formats 123
- Figure 4-4 also has 124
- Figure 4-5) 124
- 5 Non-Cinema Operation 128
- Table 5.1 129
- Figure 5-2) 129
- CP2000-SB User Manual 5-3 130
- 5.2 Selecting the Source 131
- 6 Maintenance 132
- 6.1 Warnings and Guidelines 133
- Section 6: Maintenance 134
- WEAR PROTECTIVE CLOTHING: 134
- COOL THE LAMP COMPLETELY: 134
- FILLING THE COOLER: 135
- 6.3 Maintenance and Cleaning 136
- For lens only 137
- For reflector only 137
- Figure 6-1 Install Bulb 140
- 6.5 Replacing a Lens 143
- 7 Troubleshooting 144
- 7.1 Power 145
- 7.2 Lamp 145
- Section 7: Troubleshooting 146
- 7.4 Ethernet 147
- 7.5 Cinema Displays 147
- 7.6 Non-Cinema Displays 148
- 8 Specifications 150
- 8.1 Display 151
- 8.2 Lenses 151
- 8.3 Inputs 152
- 8.4 Touch Panel Controller 153
- 8.5 Power Specifications 153
- 8.6 Lamps 154
- 8.7 Regulatory 155
- 8.8 Environment 156
- 8.9 Weight & Size 156
- Section 8: Specifications 157
- 8.10 Standard Components 158
- Appendix A: Glossary 160
- Appendix B: ASCII Messages 176
- B.1 Function Codes 177
- ASCIICODE?M) 189
- Table B.2 Error Messages 190
- CP2000-SB User Manual B-19 194
- P1 P2 Notes 195
- C.1 Serial Links to Projector 200
- CP2000-SB User Manual D-1 202
- D.1 The GPIO Port 203
- CP2000-SB User Manual E-1 204
- E-2 CP2000-SB User Manual 205
Related products and manuals for Projectors Christie CP2000-M
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
Projectors Christie L2K1500 User Manual
(36 pages)
(36 pages)
Projectors Christie DHD800 User Manual
(97 pages)
(97 pages)
Projectors Christie LW600 User Manual
(101 pages)
(101 pages)
© 2020, manymanuals.com. All rights reserved. | 1.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals