Christie CP2000-M User Manual Page 29
- Page / 205
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-12 CP2000-SB User Manual
020-100162-04 Rev. 1 (05-2009)
Section 2: Installation & Setup
2.1.3 Lens(es)
Primary Zoom Lens
1. Fully insert the lens assembly straight into the lens mount opening all the way back without turning.
With the lens fully back, it will seat properly within the lens mount. NOTE: High Contrast lenses (only)
have a flat on the rear flange. Rotate the lens so that the flange clears two screws in the mount. Also ensure
the UP label is at the top to ensure proper aperture orientation.
2. Lock the lens assembly in place with lens clamp DOWN. NOTE: The lens seals the projector head,
preventing contaminants from entering the area of main electronics. Never attempt to operate the projector
without a lens installed.
3. Calibrate the lens. See Section
2.7 Basic Image Alignment for details.
Anamorphic Lens or 1.26x Wide Converter Installation (Optional)
NOTE: Required only for 1.25x anamorphic lens or 1.26x wide converter lens producing 2.39:1 scope images.
If the anamorphic or wide converter lens will be used, it is recommended that you now add the lens—and its
motorized mount—so that the additional weight will be present when correcting later for final leveling and
boresight adjustments. Install only for those installations requiring full-size 2.39:1 scope images (mostly side-
masking screens).
1. INSTALL THE AUXILIARY LENS MOUNT ON THE PROJECTOR
At the front of the projector, install the motorized auxiliary lens mount hardware as described in the
instructions provided with the auxiliary lens mount kit.
2. INSTALL THE AUXILIARY LENS
Clamp the anamorphic or wide converter lens mount in place, following the instructions provided with the
lens mount kit. For details, refer to Section
2.8.5 Add Auxiliary Lens.
2.1.4 Install First Lamp
The CP2000-SB accommodates different lamps. Refer to Section 8.6
Lamps for a complete list of supported lamps.
1.
REVIEW LAMP PRE-WIRING
Review all lamp pre-wiring as described on the previous pages,
ensuring that all leads and harnesses are connected correctly and
that the universal cathode connector nut is secured to the rear lamp
post.
2. CHECK LAMP CRADLE (ANODE END) LOCATION FOR YOUR LAMP
• For 4.5 or 6.0 kW lamps, the lamp cradle must be as far for-
ward as possible (factory default).
• For 2.0 or 3.0 kW lamps, move the cradle to the rear position,
i.e., approximately 1” closer to the reflector (Figure 2-19).
3.
INSTALL LAMP
Refer to Steps 7-10 from Section
6.4 Replacing the Lamp & Filter. Observe all warnings, and wear
protective clothing and shielding.
Figure 2-19 Lamp Cradle Position
- Film-Tech 1
- CP2000-SB 2
- Table of Contents 10
- 1 Introduction 12
- 1.1 The Projector 13
- 1.2 List of Components 14
- 1.2.2 Software Requirements 15
- 1.4.1 Typographical Notations 16
- LP, A1 etc 16
- 2 Installation & Setup 18
- Before You Begin 19
- CP2000-SB User Manual 2-3 20
- Figure 2-3 Adjust Feet 21
- Interlocks to Projection Head 22
- Cables to Projection Head 23
- Connections to Power 23
- CONNECT LAMP LEADS: 24
- 2-8 CP2000-SB User Manual 25
- CP2000-SB User Manual 2-9 26
- Figure 2-16 Fill Reservoir 27
- 2.1.2 Exhaust Ducting 28
- 2.1.3 Lens(es) 29
- Primary Zoom Lens 29
- 2.1.4 Install First Lamp 29
- 2.1.5 Connecting to Power 30
- Warning! Ground 31
- CP2000-SB User Manual 2-15 32
- IF EXTERNAL 33
- IF INTERNAL 34
- 2-18 CP2000-SB User Manual 35
- PC/Laptop, Server or Network 36
- 2-20 CP2000-SB User Manual 37
- 2.5 Initial Power Up 38
- 2.6 Maximizing Light Output 39
- 2.7 Basic Image Alignment 40
- 2.8.1 Adjust Offset 41
- CP2000-SB User Manual 2-25 42
- Focus Left 43
- Edge Center 43
- Vertical Boresight Bolt 44
- Vertical Hold Screw 44
- Top Center 44
- 2.8.5 Add Auxiliary Lens 45
- Anamorphic (1.25x) 45
- Wide Converter Lens (1.26x) 45
- Fold Mirror Adjustment 46
- DMD Convergence 46
- Color Calibration 47
- Electronic Screen Masking 47
- PCFs (Rare) 47
- 3 Operation 48
- 3.1 Projector Basics 49
- Air Filter 50
- Breaker Panel 50
- Power Cabling 52
- Projection Head 52
- Security Locks 52
- Security Plates 52
- 3.2 Power-up Procedure 53
- 3.3 Power-down Procedure 54
- 3.4.1 User Access and Rights 55
- General Users 55
- 3.4.2 TPC Power-up Defaults 56
- 3.4.3 Failed TPC Connection 56
- 3.5.1 TPC Main Menu 58
- 3.5.2 TPC Status Menu 59
- ENVIRONMENT 61
- 3.5.3 TPC Alarm Window 63
- Responding to an Alarm Window 64
- 3.5.4 TPC Custom Menu 65
- Custom: Page-1 Menu 66
- = use full cinema processing 67
- Custom: Page-2 Menu 68
- Custom: 3D Control Menu 69
- L/R INPUT REFERENCE NOTES: 70
- L/R DISPLAY REFERENCE NOTES: 70
- L/R OUTPUT POLARITY NOTES: 70
- FRAME RATE N:M NOTES: 70
- Advanced: Preference Menu 75
- for a complete description 75
- New Lamp button activates a 76
- Table 3.11 New Lamp Fields 77
- Figure 3-18 New Lamp Fields 77
- Advanced: Lens Menu 78
- Advanced Preferences menu 79
- Admin Menus 82
- RESOLUTION NOTES: 83
- 0 (default) to 84
- Table 3.15 84
- PRESENTATION NOTES: 86
- CROPPING NOTES: 86
- LETTER BOX NOTES: 87
- : OnSite is a permanent 88
- MEASURED (MCGD) NOTES: 89
- CREATE MCGD NOTES: 89
- GAIN NOTES: 89
- CP2000-SB User Manual 3-43 90
- Record any new 91
- IP Address 92
- Figure 3-38 About Menu 96
- Section 3: Operation 100
- Table 3.22 Sample Messages 100
- 3.7 Upgrading SSM Firmware 102
- Figure 3-43 Host Setting 103
- 3.8 Working with the Lamp 104
- WHEN SHOULD I USE LiteLOC™? 105
- Figure 3-46 Setting LiteLOC™ 105
- Advanced: Lamp History menu 109
- 3.9 Working with the Lens 111
- 3.10 Working with 3D 113
- 3.10.4 Other Hardware Setups 115
- Figure 3-58 Setup for 3D 116
- 4 Cinema Operation 120
- 4.1 Compatible Cinema Sources 121
- Section 4: Cinema Operation 122
- 4.2 Image Formats 123
- Figure 4-4 also has 124
- Figure 4-5) 124
- 5 Non-Cinema Operation 128
- Table 5.1 129
- Figure 5-2) 129
- CP2000-SB User Manual 5-3 130
- 5.2 Selecting the Source 131
- 6 Maintenance 132
- 6.1 Warnings and Guidelines 133
- Section 6: Maintenance 134
- WEAR PROTECTIVE CLOTHING: 134
- COOL THE LAMP COMPLETELY: 134
- FILLING THE COOLER: 135
- 6.3 Maintenance and Cleaning 136
- For lens only 137
- For reflector only 137
- Figure 6-1 Install Bulb 140
- 6.5 Replacing a Lens 143
- 7 Troubleshooting 144
- 7.1 Power 145
- 7.2 Lamp 145
- Section 7: Troubleshooting 146
- 7.4 Ethernet 147
- 7.5 Cinema Displays 147
- 7.6 Non-Cinema Displays 148
- 8 Specifications 150
- 8.1 Display 151
- 8.2 Lenses 151
- 8.3 Inputs 152
- 8.4 Touch Panel Controller 153
- 8.5 Power Specifications 153
- 8.6 Lamps 154
- 8.7 Regulatory 155
- 8.8 Environment 156
- 8.9 Weight & Size 156
- Section 8: Specifications 157
- 8.10 Standard Components 158
- Appendix A: Glossary 160
- Appendix B: ASCII Messages 176
- B.1 Function Codes 177
- ASCIICODE?M) 189
- Table B.2 Error Messages 190
- CP2000-SB User Manual B-19 194
- P1 P2 Notes 195
- C.1 Serial Links to Projector 200
- CP2000-SB User Manual D-1 202
- D.1 The GPIO Port 203
- CP2000-SB User Manual E-1 204
- E-2 CP2000-SB User Manual 205
Related products and manuals for Projectors Christie CP2000-M
Projectors Christie CC50 Installation Manual
(36 pages)
(36 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DS+5Kc Specifications
(16 pages)
(16 pages)
Projectors Christie D4K25 User Manual
(4 pages)
(4 pages)
Projectors Christie Entero RPMWU User Manual
(60 pages)
(60 pages)
Projectors Christie DWU675-E User Manual
(12 pages)
(12 pages)
Projectors Christie LX400 User Manual
(20 pages)
(20 pages)
Projectors Christie LX601i User Manual
(42 pages)
(42 pages)
Projectors Christie LX900 User Manual
(90 pages)
(90 pages)
Projectors Christie L2K1500 User Manual
(36 pages)
(36 pages)
Projectors Christie DHD800 User Manual
(97 pages)
(97 pages)
Projectors Christie LW600 User Manual
(101 pages)
(101 pages)
© 2020, manymanuals.com. All rights reserved. | 2.808 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals