Christie CP2000-X User Manual Page 92
- Page / 164
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
BASIC OPERATION
3-50 CP2000-X User Manual
020-100031-01 Rev. 1 (03-2009)
Close the douser (shutter) to put
the projector in a cooler stand-by
mode where lamp power is reduced
to 50% of its maximum rating (or
75%, if using a 2 kW or 3 kW
lamp). Upon opening the douser
and restoring the image, the lamp
power will return to its previous
setting.
When a new lamp is installed and its serial
number recorded (Advanced: Lamp menu),
the lamp timer resets to “0” and begins
logging time for the new lamp. This total
appears in both the Advanced: Lamp menu
and the Status menu. See right.
The Status menu also shows “Total Lamp
Hours”, which is the accumulated time
logged for all lamps installed thus far. Each
past lamp log also appears in the Advanced:
Lamp History menu.
Assuming the Lamp Expiry Message
checkbox has been enabled in the Advanced:
Preferences menu (recommended), an expiry
message will appear on the TPC (as an alarm
window) when the lamp has reached its
defined Lamp Limit and should be replaced.
Regardless of the Lamp Limit chosen, never
exceed the warranted lamp lifetime by more than 20%, as an old lamp becomes
increasingly fragile and more prone to sudden failure or even explosion, which can
be damaging and dangerous. These maximum limits appear in Table 3.15.
Table 3.14. When to Replace Your Lamp
Lamp (kW) Replace BEFORE:
2.0 2880 hours
3.0 1728 hours
4.5 1080 hours
6.0 600 hours
NOTE: Hours shown here are 20% beyond the pro-rated credit warrantied lifetimes
(see page 8-3). Do not exceed.
See 6.4, Replacing the Lamp & Filter for instructions.
Over time, as the theatre screen ages and dust and dirt collects on the port window,
the theatre may no longer be achieving the expected footlamberts as reported by the
TPC. It is a good idea to periodically recalibrate footlamberts (refer back to Figure
3.26).
How Old is M
y
Lam
p
?
Figure 3.35. Lamp Hours
When to Replace
the Lam
p
Maintainin
g
Footlamberts
- CP2000-X 1
- Table of Contents 3
- TABLE OF CONTENTS 4
- Introduction 5
- (from 1.25:1 up to 8.5:1) 6
- 1.2 List of 7
- Components 7
- Purchase Record 8
- Installation & Setup 9
- 2-2 CP2000-X User Manual 10
- HEAD-TO-BALLAST: 11
- HEAD-TO-AC: Connect the 12
- 2.2 Installation 13
- Considerations 13
- 2-6 CP2000-X User Manual 14
- CP2000-X User Manual 2-7 15
- 2.3 Projector 16
- Position and 16
- Mounting 16
- CP2000-X User Manual 2-9 17
- (AERIAL VIEWS) 17
- 2-10 CP2000-X User Manual 18
- Position 19
- more between lenses 20
- and Levelin 21
- 2-14 CP2000-X User Manual 22
- CP2000-X User Manual 2-15 23
- 2.4 Installing a Lens 24
- CP2000-X User Manual 2-17 25
- Protective gear required 26
- CP2000-X User Manual 2-19 27
- 2-20 CP2000-X User Manual 28
- CP2000-X User Manual 2-21 29
- 2-22 CP2000-X User Manual 30
- 2.5 Installing and 31
- Connecting 31
- Sources 31
- 2.6 Connecting for 32
- Communications 32
- 2.7 Connecting the 33
- Ballast 33
- 2.9 Maximizing 34
- Light Output 34
- 2.8 Initial Power 34
- 2.10 Basic Image 35
- Alignment 35
- 2.11 Offset and 36
- Boresight 36
- Adjust Left/Right 37
- Figure 2.38. Adjust 38
- L/R Boresight 38
- 2.12 Fold Mirror and 39
- Convergence 39
- Adjustment 39
- 2.13 Calibrating the 40
- CP2000-X User Manual 2-33 41
- Basic Operation 43
- 3-2 CP2000-X User Manual 44
- CP2000-X User Manual 3-3 45
- 3-4 CP2000-X User Manual 46
- 3.2 Power-up 47
- Procedure 47
- 3-6 CP2000-X User Manual 48
- 3.3 Power-down 49
- 3.4 Introduction to 49
- Controller 49
- 3-8 CP2000-X User Manual 50
- 3.5 Using the 51
- Touch Panel 51
- 3-10 CP2000-X User Manual 52
- CP2000-X User Manual 3-11 53
- BASIC OPERATION 54
- BASIC OPERATION 55
- STATUS:SYSTEM MENU ENTRIES 56
- 3-16 CP2000-X User Manual 58
- (SAMPLE) 58
- CP2000-X User Manual 3-17 59
- 3-18 CP2000-X User Manual 60
- CP2000-X User Manual 3-19 61
- Menu Functions 63
- 3-22 CP2000-X User Manual 64
- CP2000-X User Manual 3-23 65
- 3-26 CP2000-X User Manual 68
- ADVANCED / USER MENU OPTIONS 69
- Figure 3.17. Access Rights 71
- below 72
- (default) to process all 73
- ADMIN / SCREEN MENU OPTIONS 74
- CP2000-X User Manual 3-33 75
- 3-34 CP2000-X User Manual 76
- ADMIN / GAMUT MENU OPTIONS 77
- 3-36 CP2000-X User Manual 78
- 3-38 CP2000-X User Manual 80
- CP2000-X User Manual 3-39 81
- Con t r ol l er 84
- 3.6 Remote Control 85
- Table 3.12. Sample Messages 87
- fans to 88
- Figure 3.32. LiteLOC 89
- Expiry 89
- LampLOC 90
- CP2000-X User Manual 3-49 91
- (kW) Replace BEFORE: 92
- 3.8 Working with 93
- 3.9 Working with 94
- A and B 95
- 3-54 CP2000-X User Manual 96
- Figure 3.39 97
- Increasing Frame 97
- Rate by 4:2 97
- Figure 3.40. Setup for 3D 97
- 3-56 CP2000-X User Manual 98
- 3.10 Working with 99
- Servers and 99
- Diagnostics 99
- 3-58 CP2000-X User Manual 100
- CP2000-X User Manual 3-59 101
- Cinema Operation 103
- 4.2 Image Formats 104
- CP2000-X User Manual 4-3 105
- 4-4 CP2000-X User Manual 106
- Cinema Source 107
- 4.3 Selecting the 107
- 4.4 Adjusting the 108
- Cinema Display 108
- Non-cinema Operation 109
- (ALL DIGITAL RGB 8-bit) 110
- 5.2 Selecting the 111
- Maintenance 113
- 6-2 CP2000-X User Manual 114
- 6.2 Maintaining 115
- Proper Cooling 115
- 6.3 Maintenance 116
- CP2000-X User Manual 6-5 117
- 6-6 CP2000-X User Manual 118
- 6.4 Replacing the 119
- Lamp & Filter 119
- 6-8 CP2000-X User Manual 120
- Figure 6.1. Install Bulb 121
- 6-10 CP2000-X User Manual 122
- (EXAMPLE) 122
- CP2000-X User Manual 6-11 123
- 6.5 Replacing a 124
- Troubleshooting 125
- Or Dimness 126
- 7.3 TPC 126
- 7.4 Ethernet 127
- 7.5 Cinema 127
- Displays 127
- 7.6 Non-Cinema 128
- CP2000-X User Manual 7-5 129
- Specifications 131
- (near Panel B, at front) 132
- SPECIFICATIONS 135
- (for opening of lamp door) 136
- Glossary 137
- A-2 CP2000-X User Manual 138
- CP2000-X User Manual A-3 139
- A-4 CP2000-X User Manual 140
- CP2000-X User Manual A-5 141
- A-6 CP2000-X User Manual 142
- CP2000-X User Manual A-7 143
- A-8 CP2000-X User Manual 144
- CP2000-X User Manual A-9 145
- A-10 CP2000-X User Manual 146
- ASCII Messages 147
- ASCII MESSAGES 148
- B.2 Messages with 151
- Multiple 151
- Parameters 151
- Table B.2. Error Messages 152
- Table 3.1 153
- (SST?0) will trigger general 154
- System Integration 157
- C-2 CP2000-X User Manual 158
- Repacking the Projector 159
- Use of Anamophic, 3-52 163
- Offset, Vertical, 2-11, 8-1 163
- Voltmeter, 3-3 164
Related products and manuals for Projectors Christie CP2000-X
Projectors Christie CP2000-M Setup Guide
(74 pages)
(74 pages)
Projectors Christie LW551i User Manual
(128 pages)
(128 pages)
Projectors Christie LX650 User Manual
(6 pages)
(6 pages)
Projectors Christie 38-VIV208-03 User Manual
(56 pages)
(56 pages)
Projectors Christie LWU420 User Manual
(29 pages)
(29 pages)
Projectors Christie DWX951 User Manual
(8 pages)
(8 pages)
Projectors Christie CP2000-ZX Setup Guide
(58 pages)
(58 pages)
Projectors Christie D4K25 User Manual
(6 pages)
(6 pages)
Projectors Christie Mirage WQ-L User Manual
(80 pages)
(80 pages)
Projectors Christie 35/70 Operator's Manual
(56 pages)
(56 pages)
Projectors Christie DWX951 User Manual
(45 pages)
(45 pages)
Projectors Christie CineIPM-2K User Manual
(122 pages)
(122 pages)
Projectors Christie HD8K User Manual
(8 pages)
(8 pages)
Projectors Christie CS50-D100U User Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 1.301 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals