Christie CP2000-M Specifications download pdf (Page 20)

2-10 CP2000-M/MR Service Booklet

020-100220-02 Rev. 1 (07/08)

Section 5: Parts and Module Replacement

2.5.5 TOP LID

(3 minutes)

1. Use a #2 Phillips to loosen the 7 captive screws

securing the top lid to the projector housing (Figure

2-4

2. Unlock the rear lamp door using the low security

key.

3. Lift the lid up from the rear of the projector and pull

it away from the 2 tabs on the front skin.

4. When reinstalling, align the front 2 tabs and reverse

the above steps.

DANGER

UV HAZARD: When servicing the projector with the top lid removed anyone

within the immediate vicinity must wear safety glasses with side shields.

FIGURE 2-4 REMOVE TOP LID

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 121 122

CP2000-M/MR 1
TABLE OF CONTENTS 6
1 Introduction 8
1.2 PROJECTOR DESCRIPTION 10
1.3 HOW THE PROJECTOR WORKS 10
2.1 ORDERING PARTS 12
2.4 REPLACEMENT PROCEDURES 16
2.5 EXTERNALS AND CONSUMABLES 17
2.5.2 LENS FLAGS 18
2.5.3 AIR FILTER COVER 19
2.5.4 INTAKE AIR FILTER 19
CAUTION 19
2.5.5 TOP LID 20
2.5.6 REAR LAMP DOOR 21
IGURE 2-6 CDP MOUNT 22
2.5.8 CARDCAGE PANEL SKIN 23
2.5.9 EXHAUST PANEL SKIN 23
2.5.10 FRONT FACE SKIN 24
2.5.11 LAMP DOOR FRAME SKIN 24
2.5.12 INTAKE DUCT 25
2.5.14 REMOVE LAMP 28
WARNING 28
2.6 LAMP COMPARTMENT 29
2.6.2 MAIN BLOWER ASSEMBLY 30
2.6.3 LAMP ADJUSTER ASSEMBLY 31
2.6.6 UV FILTER 34
2.6.7 LAMP DOOR INTERLOCK 35
2.6.8 LAMP BALLAST 35
FIGURE 2-29 REMOVE BALLAST 36
FIGURE 2-30 BALLAST FAN 37
2.6.10 AC LINE FILTERS 38
2.7.1 CARDCAGE MODULE 39
DANGER 39
FIGURE 2-33 ALIGN TAB 40
2.7.3 INTERFACE BOARD 41
FIGURE 2-35 42
2.7.4 PROCESSOR BOARD 43
2.7.6 MOTHERBOARD 43
FIGURE 2-36 REMOVE SDB 44
A SDB Screws (2 of 4 shown) 44
A Blue SW 2 Center Channel 45
B Brown SW 1 Center Channel 45
FIGURE 2-38 GRN TERMINAL 45
FIGURE 2-40 FEEDING HARNESSES 46
A Harnesses (Remove) 50
B 2 of 4 Screws 50
C Harnesses (Remove) 50
2.7.10 LVPS RAIL ADJUSTMENT 51
FIGURE 2-54 QUICK DISCONNECTS 56
2.8.3 INTEGRATOR ASSEMBLY 57
2.8.6 COLD MIRROR 60
2.8.7 FOLD MIRROR 1 61
FIGURE 2-65 REMOVE YNF 62
2.8.9 SHUTTER ASSEMBLY 63
2.8.10 LIGHT ENGINE 64
3 Troubleshooting 69
3.1 OVERVIEW 70
3.2 TROUBLESHOOTING TREES 71
Section 4: Troubleshooting 72
3.2.3 LAMP WILL NOT IGNITE 73
3.2.5 LampLOC™ Not Working 75
3.2.6 LiteLOC™ Not Working 76
4 Serial Communications 82
EXAMPLES: 98
STANDBY mode 100
ON and lamp OFF 100
ON and lamp ON 100
020-100220-02 Rev. 1 (07/08) 101
5 Specifications 109
5.1.10 D-Cinema Ports 111
5.1.8 Axial Focus 111
5.1.11 Graphic Ports 112
5.2.2 Ethernet Auxiliary Port 112
5.2.4 RS232-B Port (PCM) 113
5.2.5 GPIO Port 113
5.4 POWER REQUIREMENTS 114
5.5 LAMP 114
5.6 PHYSICAL SPECIFICATIONS 115
5.7 REGULATORY 115
5.8 ENVIRONMENT 116
6 Interconnections 117
6.1 INTERCONNECT DRAWING 118
Appendix A: Block Diagram 119
A.1 BLOCK DIAGRAM 120
Appendix B: Shutter Override 121
B.1 SHUTTER MANUAL OVERRIDE 122

Comments to this Manuals

No comments

Christie CP2000-M Specifications Page 20

Comments to this Manuals

Related products and manuals for Projectors Christie CP2000-M